I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I am trying the IOS app and I tried to set the alarm on the "out of range" event with the beacon
It doesn't fire the alarm although I am trying an Android phone with same...
I am trying to run the debug project for ble_app_hrs following the steps in "nAN-29 nRF51 Development with GCC and Eclipse Application Note v1.1.pdf"
but I get this error...
Given that most of the SDK (including the softdevice hex) is public now due to the mbed support: would it be possible to open up the downloads for the standard nRF51 SDK and...
From the s130 release notes:
GAP
Concurrent Central, Peripheral,
Broadcaster and Observer operation
(DRGN-4354).
Up to 4 simultaneous
active connections...
Hi.
I am trying to modify the bootloader example provided by nordic.
I am able to compile/link my code and use nRFgo studio to run it, but for some reason I can not debug...
Hello,
i´m using nRF51822 with S110 SoftDevice to transfer data from Sensors that will be read out via I2C by the Nrf51822.
I have read some topics about how it is not...
Hi,
I bought nordic evaluation board 2 days ago. I have been searching through the forums to enable and test the voltage level of a battery and monitor it via UART. After...
Hello all,
Is it possible for a nRF51822 to read information from another peripheral Device using broadcasts or advertisments?
I have an application where I need to...
hi,
I have been reading some posts regarding similar issues, but I am not able to nail down this one.
I am trying to create a custom 128 UUID and associate some Service...
I overwrited the application program which made with v5.1.0 and it included only difference against the v5.1.0 to sdk v6.1.0. After this, I buidled it but the target didn...
I am looking for a dev kit which would allow me to try out SoftDevice S130, will I be able to use S130 if I buy any of these:
nRF51822-mKIT
nRF51822 DK
nRF51822 EK...
The nrf51 reference manual shows timing diagrams for the TWI interface when reading from slaves to have a shortcut between BB and SUSPEND. My assumption would be that's there...
I am using the ble_app_uart code from SDK 6.0 on my custom PCB with a nrf51822. I am comparing it's functionality with a PCA10004. Both are running the exact same code. I...
Hi all,
some time ago we bought a nRF51822 Evaluation Kit with the PCA10001 being Version v2.0.0.
Why exactly is it not recommended to work with the new SDKs such as SDK6...
Has anyone played with getting the iBeacon reference kit/software to run with the SD7.0 code?
I'm wanting to change from the boot loader + SD 6 + app to a simpler SD 7...
