Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi,
I am using the nRF52832 and I have been trying to meausre the centre frquency on a specturm analyser. But, the centre freq on the specrum analyser is 1.81GHz when it...
Hi,
I have a beacon that uses 4 AA batteries, each has 1.5V and 2600 mAh. When connecting the board to the PPK I get the attached measurements when doing a lot of scanning...
Hey guys. We are using the NRF52 with SDK 13.0.0.1-alpha.
If we connect the NRF52 to our own android or iOS APP we have some timing problems with notifications. When the...
I would like to reduce current consumption on my beacon and I wonder if it is possible to disable sending scan response. I know that it is not a huge difference in a single...
Firstly，the RedMi Note3 DFU failed used by dual bank，however Xiaomi3 Phone can DFU successfully.As the question link text mentioned,the process of the RedMi Notes3 Phone DFU...
Hello Nordic,
i am trying to interface BME280 with nordic nRF52 and SDK v 12.02 using twi_peripheral but i am unable to do it. here in example they are using ls75b whereas...
How do you setup "immediate Service Alert" Client on iOS, in order to get notified when an action is taken on the bluetooth peripheral ? (eg. Button press)
Hi all, I have an nRF52832 which is woken up every 15 seconds by an RTC to check for ESB broadcasts. The nRF52 will be powered continuously until the battery runs out, so...
I want to use AES ECB block present on nrf51 and nrf52 boards for resolvable private address (RPA) generation.
Are there any measurements about how much battery the...
I have an iot/coap environment setup and i want to read input voltage connected to p0.01.I can read the input in terms of resolution(0-1023).I can convert this values to voltage...
I have a project where I need both TWI instances as well as an SPI instance to be used with sdcard and fatfs libraries. When I try to compile I get the error: SPI1_TWI1_IRQHandler...
hi,everyone,I want to ask who know why sdk11.0 ble_ancs push message without push App Identifier?I look at the print, push the news started with tittle ,and the "p_attr -...
Hi!
I'm trying to use a custom made whitelist with my scanning device, but no data is arriving.
Is there something I need to do at the advertising devices? Here is the...
Hi, I have a custom board based around the nRF51822 which I programmed via SWD with the ble_app_hrs_pca10028_s130.hex image provided in the SDK, however when checking with...
