But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I'm trying to use the BLE sniffer in a quite busy BLE environment. Unfortunately, it always crashes after a few seconds.
I'm using:
ble-sniffer_win_1.0.1
nRF51 Dongle...
Hi,
i am using PCA10040 DK board,
working on ble_app_Uart example, i have created one timer(app_timer) here is the code:
printf("init\r\n");
ret_code_t err_code;...
Dear all,
My chip is nrf52832, and sdk version is SDK12.1.0_0d232a. And tried to use ble service and spi master function.
I create a timer to send spi command every...
hello all:
my mcu is nrf51822(QFAA), and use it to make a blue device ,i want to use mcu's reset pin to reset it, just use hardware. i add a key to connect the reset pin...
Hi,
I have searched for examples which will use passkey to connect with android, but didnt find any.
I want ble_app_hrs example to connect with nRFConnect in android by...
HI，i develop my project base on “examples\ble_peripheral\ble_app_uart” and “nRF UART v2.0”。i hava large data transmit from phone（androd） to nrf52832。
but when send a package...
I need to save some data on the flash storage. This data will be some structures and I will write, read and modify them as and when required. I am also using peer manager...
Hello
I came across interesting problem I couldn't find answer to.
In my project bss size printed by arm-none-eabi-size is larger than the value that can be calculated...
I'm testing with ANCS example(SDK11.0.0), PCA10028 and Iphone, observing packet with sniffer.
at the first connection,
master sent EDIV( 0x0 ), Rand( 0x0 ), SKDm and...
I'm using an Nrf52 with S132v3.0
I'm using Peer Manager to manage pairing and bonding.
I'm running as a central connecting to a peripheral (iOS/Android peripheral).
I...
Is there any way for the application to be notified by the S110 when a central reads/scans an attribute in the peripheral in response to its broadcast?
There are events...
hi,all
i use use dongle as packet sniffer.when the phone can not connect my device,the dongle can not receive CONNECT_REQ PDU.if the phone can connect with my device,the...
Hi,
I am using legacy version of DFU for my application and would like to use the appropriate version. However, using pip the only available versions are 1.1.1 and beyond...
Dear NORDIC
I have one strange issue:
My nRF52 app work well, then I use Android phone connect to it, it's OK.
Then Android phone cancel pair, so nRF52 disconnect,
...
