I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
hi,
i tried nrf51822_beacon_app.hex( C:\Nordic Semiconductor\nRF51822 Beacon v1.1.1\Source Code\nrf51_beacon\ble_app_beacon\pca20006\s110\arm_build\ ).in that we changed...
This might not be the correct place/forum to ask this question.
Since a couple of days, I am not able to step or next with gdb .
I understand that gdb needs to know what...
Hi：
Now keil4 default is to use the 16_bit THUMB instruction set, if I want to set it to start the program using the 32_bit ARM instruction set, how should we do? thanks
Hi,
After reading some questions about these topics I became a little confused.
I want to count milliseconds, so should I use Systick_Handler or use Real Time Counter...
Edit 1
To narrow down I did this... Below is ble_dfu_init() from ble_dfu.c.
uint32_t ble_dfu_init(ble_dfu_t * p_dfu, const ble_dfu_init_t * p_dfu_init)
{
uint32_t...
I am running NUS and a custom service.
I have updated vs_uuid_count = 2 in softdevice_handler.c
Following other posts on the forum, I have stepped through the code using...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Hello everyone
I was not able to find any explicit statement regarding the use of the TWI_APP with easyDMA on the nRF52 series and SDK13.0.0.
I checked the examples...
Hello guys,
I am currently looking at the recommended schematic QFN48 with internal LDO setup and I have a few questions (sorry, if they are silly, I am a newbie).
...
Hi, I'm working on an extremely space-tight design and need some clarifications. It is an nRF52832 QFAA chip with a Johanson 2450AT18B100 chip antenna.
Up to this point...
Hi,
I would like to use higher dBi antenna instead of the DK pcb antenna. Can I say the pi-network before J1 (measurement point) probe is 50ohm? Hence I can just remove...
I am trying to control another BLE device with nRF52xx. For controlling the device I need a terminal for connecting, disconnecting and switching on & off a sensor. I have...
I am using NRF52DK and trying to debug an SPI transfer, using SEGGER_RTT.h to print. However, printing of the logs are not consistent. Some debug lines do no appear in the...
Hello,
The only semi-official information that I can find regarding the differences between PCA10040 1.1.0 and 1.1.1 DK boards is this post . It suggests that there are...
