Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I've just noticed that it's possible to call ble_advertising_init() and ble_advertising_start() with params that are quite conflicting.
ble_adv_modes_config_t advertising_modes_config...
Hi dear Engineers!
We want to add Eddystone compatibility to the device.
Is it possible use nRF52 silicon radio ?
How I understand, it is not compatible with any SDxxx...
After a few minutes of running, the Power Profiling kit will start printing out "Range not detected" messages in the console. It appears to be related with the "Average" window...
Hi,
I am using mca8652fc and used device address as #define ACCELEROMETER_ADDR 0x1D
but it is not reading WHO_AM_I register properly.
I used #define ACCELEROMETER_ADDR...
I did try SPI interface between nRF52-DK and MAXIM11300.
Unfortunately, I did not successfully it work.
I used SDK_11.0.0 on nRF52-DK 0.9(Engineering B) and that
...
Hello, according to devzone.nordicsemi.com/.../ it was an example in nrf51 sdk 6.1.0. I checked it and found no files or folders related, not in sdk 6.0.0 or sdk 7.0.0 Could...
Hi,
I need to send my packets with an interval smaller than 100ms in unconnectable mode. I know, that this is a restriction from Bluetooth standard. For my application...
Hello,
I've a problem with handling interruption on nrf51dk (SDK12.1.0).
I set GPIOTE to handle interruption based on the example code "pin_change_int".
I work with the...
I am trying to use the NRF51 soft device with the App_PWM library. I can get both working individually, but when I try to enable both, I can no longer connect to the device...
Hi ,
I am trying to interface SD card with nrf52. For this I am using fatfs example of new 12.0 sdk. I can able to write the data to file but when I am taking the data...
HI,
I followed this link github.com/.../nRF51-ble-bcast-mesh to develop mesh in nRF51822 dongles. i am able to flash the code( nRF51-ble-bcast-mesh/nRF51/examples/BLE_Gateway...
Hello, I am working on characteristics tutorial.(our service.c)
And I succeeded in notifying characteristic from nordic to android.
The methods I used to notify characteristic...
I'm in the process of migrating to SDK 12.2 and I noticed that nfu_dfu_settings.c now includes app_scheduler.h and makes a call to app_schedule_execute().
How do I use...
want to send a float as a value of a characteristic
I have successfully achieved this using the simple way
Below is the example of just two float variables in an array...
