Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
I just made it to upload the example to the device. I'm new into firmware development btw.
I changed the timeout so the beacon will stop advertising after 120 seconds but...
Hello, I have implemented the code below for my project
based on switching central and peripheral role in S130.
The code works fine on the Devkit PCA10028 but on porting...
In compatibility matrix it is shown that s110 v 7.3.0 is compatible with nrf51422 when using SDK 7.x.x. But when I downloaded s110 v7.3.0 in its name and specification documents...
I tried to build the example project "ble_app_uart" bundled with nRF5 SDK (nRF5_SDK_11.0.0_89a8197) within the MDK-Lite V5.18K. It failed and I got the following messages...
Hi!
I am attempting to flash sdk11 examples onto a QFAB board compiled using arm-gcc over JLINK SWD p20 via the NRF-51DK.
While running make flash, the nrfjprog command...
Hello I found example for dual bank bootloader ("examples\dfu\bootloader\pca10040\dual_bank_ble_s132"). And it works well.
Do you plan also to add a SINGLE bank boot-loader...
hi all,
I am using SDK version 8.
i want to make button as ON and off switch.
REQUIREMENT:
When button is pressed counter should keep on incrementing when i released...
Hello,
I would like to simulate the spreading of a disease using the nrf51822 beacons. My question is if my envisioned project is possible as I'm completly new to nrf51822...
I would need to change a timer into single shot mode. My code is as follows:
static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE(MY_SAMPLE_TIMER);
nrf_drv_timer_init...
using S130, SDK11,
CANNOT work the two heart rate sensors which have the different deivce name ?
when it connected the heart rate sensor A and eveything is OK.
but...
Hello,
I want to use nRF52832 at 2V. But I am not sure what would be the current consumption of radio during transmission and reception with DCDC regulator on. In datasheet...
Hi, after some research and reading several posts (especially this one ), I am still confused about the Flash endurance on the nRF52.
In the product specification for the...
Hi,
I developed a device and I ship this devices to custemers. Now I want to update firmware of this devices with user friendly app. Is there any app updating app for customers...
