Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
Hi,
I'm developing to nrf51822 mcu, using a s130 softdevice.
I'm using a BLE example code.
I get an interesting problem - when the mcu receives 2 reports (that are...
Hi,
we are thinking about using the NRF52 with the BLE SoftDevice in a security relevant application. As the SoftDevice is not available as source code, no reasonable security...
Hi all!
I want to check work of AES encryption.
Some code on 51822:
uint8_t aesKey[]= {0x31,0x32,0x33,0x34,0x35,0x36,0x37,0x38,0x39,0x30,0x31,0x32,0x33,0x34,0x35,0x36...
Hi All,
I have a problem with the function sd_ble_gatts_hvx().
I have no return value when i call this function and i don't understand why ?
I have a function where...
I am running SES 3.10f on Linux. I have followed the Tutorials regarding Monitor Mode Debugging. I don't ever get the pop up box regarding the Monitor Mode debugging license...
Hi All,
My question is about available sleep modes in nRF51822.
As I can find in nRF51 Series Reference Manual, and Product Specification documents, nRF51822 chip has...
Description:
I am developing iOS app which will connect BLE and keep the connection till user don't want to disconnect. i.e we want to autoconnect BLE when BLE is in range...
Using Master Control Panel (MCP) with nRF51 Dongle PCA10000 v1.0
Segger is offering a J-Link firmware update - v6.10l:
Is this compatible with MCP? Is it safe to...
I am using RedBearLab Blend v1.0. I ran the HID_template and HID_keyboard_template. I can see the device in Win10 advertised as joystick and keyboard. Then I tried to modified...
Hello , i am going to use nrf51822 development kit ,but i am totally new for using it, i want to know that if i have development board and i want to see result but i dnt have...
Hello,
I need a little help regarding IoT-SDK 0.8.0 on nRF51.
In the MQTT-Example connection to the broker is established only when I press the button (callback), but...
Hi all,
I am facing issues when initializing and enabling the Softdevice after using the nrf_nvmc driver to erase and write flash pages. The project shall have the ability...
I am working with a MacBook Pro (El capitan) and the nRF51822 beacon and I need to measure the RSSI. I understand that the app nRF connect can do it, but the antenna on my...
Scenario is as follows:
NRF52 (SDK12.1, SD3.0) works in central and peripheral mode.
What happens is that on start we create a single shot timer with 4.2second to wait...
I write a function, It can read ok without BLE starting.
When I start the BLE , the function can not run.
So I think that , if I can use some function to stop the stop the...
