Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hello.
Is it possible to use multiple serial communication on 52832?
What i mean, first serial port uses for communication with custom board' micom chip.
The second...
Hi everybody,
I'm developing an product with :
NRF52840, V0.9.0, SDK15
I want to put the MCU in sleep mode (system on) and wake up with NFC or by timer (for example...
Hello,
What is the reason why my homemade PCB half passes through NRF_POWER->DCDCEN = 1; after broadcasting DCDC does not work? How do you need to solve it?
We will get a beacon from China. But how do we know if the chip is original? If I can read the unique device id, can I say it is original? Or is there another way?
I am working on the twi_sensor example,when i compiled the code it is showing as undefined symbol "data_handler(refered from main.o)", what are the changes i need to make...
Hi,
I was successfully changing mac address dinamically DURING ADVERTISING on nrf51822 chip at each ble_radio_notification event, in this way:
Before start advertising...
Hello
How do I activate Brown-out reset? I estimated there need to set some register/registers, but I cannot findout.
Possibly Brown-out reset function is always enabled...
Hello,
I work on project for BLE communication in DFU mode.
I am testing according to the mode defined on the Nordic web page link
I did the tests with the BleuZ and...
checking most of the reliable coin cell CR2032 such AS Panasonic declare on very very low current transfer far lower then 5 mA
if i set my Ble in 5mA IO OUT ....when my...
NAND or NOR flash memory to use with nrf25832? my application is to store the data from mpu-9255 to flash memory. my data rate is about 3 mega byte per hour and i have such...
Hi,
I am using Linux ubuntu 14.04 with kernel version 4.15.0-041500-generic for 6lowpan over BLE and MQTT broker wit IPv6 address as inet6 address in below image
In...
If I use DeveloperStudio_1_1_3139_0 to generate a profiles and services for the latest SDK 15.x, will it correctly work?
I recall back with SDK 11/13.xx it was not compatible...
I need to sample ADC channel at the fastest deterministic rate.
If i use burst mode with 3us acquisition time, do i get a sample exactly every 5us?
does t(conv) is always...
About example BLE_uart,
My device must always remain in advertising, I'm using a 1280 ms between two advertisng event.
I have to minimize the consumption during advertining...
