I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello,
I am using sdk 11 and I am refering to code ble_app_uart. I am using nrf51 and I want to add passkey to this code. So do this I added
// Add static pin:
uint8_t...
Hi,
I measured the throughput using the ATT_MTU Throughput Example.
I referred to Testing in the following URL.
infocenter.nordicsemi.com/.../ble_sdk_app_att_mtu.html...
Hi,
Is Ibeacons are normal advertising packets ?
Will all the BLE Central which scan receive this ibeacons ?
Can I use NRF51822 as a device which receive the ibeacon...
as far as I am concerned, when I use PPI or SHORTS without interrupts, I DON'T need to clear the corresponding event registers, and task will be triggered once the event is...
Hi, Noric
When I use Master Control panel to connect my nRF52 for DFU, it shows:
Then when I press "Start", it shows:
Plz help me.
Which example will be flashed...
Hi everyone. I am working on a project while doing my undergrad in EE and am confused on a few things.
I am using Raspberry Pi 3s with the NRF24L01 (NRFL) chip and code...
Hello!) Have some problem with custom pcb, created for nrf52832. After mounting all components a connected pcb to nrf52dk through P20 port. Chip was correctly detected in...
Hello,
I faced the problem of high power consumption when using a large number of the inner periphery.
Currently used:
SPI1 -> Accelerometer, ext. serial memory
TWI0...
Hi,
I am facing an unusual issue. My team has created a custom board using nRF52 and testing with HRS sample from ble_peripheral folder. Using the nRF Connect mobile app...
I've heard of a Bluethooth device called a N51802 QFAA0, which is possibly a nRF51 rip off / clone.
Has anyone else heard of this.
From what I've been told its fitted...
I'm tryinng to minimize jitter on my LED when I switch between .2 .4 .6 .8
I'm using a nrf51822 for my testing. The jitter is so bad that it has a strobe effect.
I reviewed...
Hello. I have a question and a request for Nordic developers.
It is really super-helpful that in SDKV12 you converted to having a master sdk_config.h that contains what...
Hi
I tried to update the nano-pb library that comes with the SDK 12.2 for signed DFU to a higher version. The version in the SDK has "0.36 dev" and i tried to update it...
