hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi Nordic,
My application does the following:
Timer 2 takes care of controlling a shift register (CLK and DATA)
Timer 1 takes care of polling data from sensor...
Hi!
I am in the process of upgrading a quite large project from SDK 8.1 to SDK 12.2. It uses the nRF52 DK, PCA10028. I still use the toolchain I stated with, including...
Following this tutorial , but for pca10028 , softdevice s130 instead. I'm on Linux.
Under "Running", when I press Ctrl + F5 , I get the error s130_nrf51_2.0.1_softdevice...
Hi,
I try to modifie ble_multilink example et send more than one data,
here is my main code code :
static uint8_t test[4] = {0x41, 0x42, 0x43, 0x44};
static...
Hello,
SPIS is adding a 350uA from 80uA baseline running current. I would like some tips and advise on improving this. Thanks!!!
The baseline operation consists of:...
I am using eclipse as IDE , but when i build ble_app_hrs example it's getting an error ../../../../../../components/ble/ble_advertising/ble_advertising.c:195: undefined reference...
I have a 32u4 Feather but don't get the right support from Adafruit to create my own Profile. I have downloaded Nordic's android app and can see all the characteristics on...
Hi.
I'm trying to enable and disable softdevice repeatedely.
In my code, softdevice is firstly enabled then advertising properly.
After some seconds, softdevice is disabled...
Hi,
I used the ble_peripheral and ble_central example and I send messages from one to the other.
Know I need to do the same with multilink.
I managed to connect ble_multilink_central...
hi dear Engineers!
the questions is it possible to use RX RF reciever to estimate the average BW RF signal input power like I do it in Semtech 433/868 RF SoC to make desicion...
hi, all
my nrf52832 can not run good when download the program into the flash, and can not run good in debug session mode without breakpoint ， but if I add one breakpoint...
Hi,
I am trying to send L2CAP connection reply by using this "sd_ble_l2cap_ch_conn_reply()",but i am unable to see the packet on wireshark. The incoming connection handle...
Hi I note here that it is recommended to apply solder mask to the ground layer beneath the nRF24L01+ exposed die so they don't connect:
devzone.nordicsemi.com/.../
But...
I'm finding a discrepancy with numbers between the nwp_008 whitepaper (quarterwave printed monopole antenna for 2.45ghz) and AppCad values.
I've assumed you can measure...
Hi.
Months ago I loaded the nfc_url_record example and it worked fine.
Later some time I updated the packages, and since then that particular example gives errors.
The...
