I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hello
I’m aware that this topic has been discussed in several posts from a couple of years ago, but I haven’t found a concrete solution yet.
I'm currently using an external...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
If I set the I2S peripheral on the nRF52 to mono, ie CHANNELS is either LEFT or RIGHT, what does it actually output? I'm sure it still toggles the LRCLK line to indicate left...
I'm working on a battery - operated device where the battery is soldered onto the device, which makes it inconvenient to pull power to the device. I might be able to get to...
Hello,
I have some problem in DFU.
I ask this again.
I did as below.
Key generation
nrfutil keys generate c:\vault\priv.pem
public key generation in...
Dear Nordic Team,
I can't launch Sniffer on PCA10000 using MCP nor on PCA10040 using nrfConnect. In case of MCP I get "No response from master emulator" and in nrfConnect...
Hi,
is someone of you aware of a portable (Win, Linux, OS/X) GATT client library, prefereable with C++ binding? The only one, that I've found so far is Qt. What do you use...
I have been using nRF8001 equipped Arduinos for a few years now with great success. I exclusively use apple software on the other end. I have a new application that will required...
i want use a 9 axis IMU sensor (3 axis accelerometer,3 axis gyroscope and 3 axis magnetometer) in nrf51822 is it possible and how the transmission of values takes place.....
Hi,
I'm using the bootloader in nRF5_SDK V12.0 with nRF52832. I have some problems want to know:
How to make it run application first after I program softdevice...
I notice that the track which runs from P0.11 (E4) is connected to GND at pads C3 and C4. Is this intentional? If P0.11 is required for GPIO usage, is it necessary to go to...
I am trying to update my project to SDK 12.2 which was released this week and I am getting a ton of compiler errors with the FreeRTOS source files. For example, I try an compile...
I'm a begineer in nRF52DK and S132.
I am trying to make an application code to enable link layer control procedures at any time in a connection state with the nRF52DK and...
hello everyone，
Which APP demon is the most stable APP？
I use nrf-master APP to test the blue device，it can connect very well。but when I use uart-app ， it can't connect...
I notice that if Make virtually any of the SDK12 armgcc examples that I get a warning that 2 include folders do not exist
e.g.
../../config/ble_app_hrs_pca10028_s130...
