We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
My question may seem silly, I did not so long ago been programming NRF51822 S130. I use examples experimental_ble_app_blinki. I want to get the module ID smartphone when connected...
If I set the I2S peripheral on the nRF52 to mono, ie CHANNELS is either LEFT or RIGHT, what does it actually output? I'm sure it still toggles the LRCLK line to indicate left...
I'm working on a battery - operated device where the battery is soldered onto the device, which makes it inconvenient to pull power to the device. I might be able to get to...
Hello,
I have some problem in DFU.
I ask this again.
I did as below.
Key generation
nrfutil keys generate c:\vault\priv.pem
public key generation in...
Dear Nordic Team,
I can't launch Sniffer on PCA10000 using MCP nor on PCA10040 using nrfConnect. In case of MCP I get "No response from master emulator" and in nrfConnect...
Hi,
is someone of you aware of a portable (Win, Linux, OS/X) GATT client library, prefereable with C++ binding? The only one, that I've found so far is Qt. What do you use...
I have been using nRF8001 equipped Arduinos for a few years now with great success. I exclusively use apple software on the other end. I have a new application that will required...
i want use a 9 axis IMU sensor (3 axis accelerometer,3 axis gyroscope and 3 axis magnetometer) in nrf51822 is it possible and how the transmission of values takes place.....
Hi,
I'm using the bootloader in nRF5_SDK V12.0 with nRF52832. I have some problems want to know:
How to make it run application first after I program softdevice...
I notice that the track which runs from P0.11 (E4) is connected to GND at pads C3 and C4. Is this intentional? If P0.11 is required for GPIO usage, is it necessary to go to...
I am trying to update my project to SDK 12.2 which was released this week and I am getting a ton of compiler errors with the FreeRTOS source files. For example, I try an compile...
I'm a begineer in nRF52DK and S132.
I am trying to make an application code to enable link layer control procedures at any time in a connection state with the nRF52DK and...
hello everyone，
Which APP demon is the most stable APP？
I use nrf-master APP to test the blue device，it can connect very well。but when I use uart-app ， it can't connect...
