So I will have 2x physical UART provided on my board. I am using printk(), and I want to choose which UART handles console traffic by config options.
How to achieve that...
I have been working with 2.9.1 but went back to a project using 2.6.1 to flash a nrf5340dk and can still compile it, but now cannot flash the nrf5340dk. I am getting this...
Hello,
I'm trying to use SLM application on ctcc/nrf9161 hardware ( https://github.com/nrfconnect/sdk-zephyr/tree/main/boards/ct/ctcc ) however it seems I'm not able to...
Hi, I have to integrate on my MQTT application , location library using GNSS. Actually I am using location library on cellular. I want to use exclusively GNSS. I am developing...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
Hello!
I want to develop a Heartrate Monitor Device which uses BLE and ANT+ using the Seeed XIAO nRF52840 Plus Board.
Now that I have the board I found out that ANT doesn...
created a new BSP PCA10001 from PCA10028 and replaced the CFLAGS += _DBOARD_PCA10001 for uart example in peripheral folder using sdk 10.
Migrated simple_uart example &...
Hello,
I wish to communicate with the chip via SPI NRF51822.
The NRF chip is configured as a slave. Based on the SPi_slave_example code, I can't set to 1 the semaphore...
I configured my system to sleep after inactivity time.
nrf_gpio_cfg_sense_input(WAKE_UP, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_SENSE_HIGH);
err_code = sd_power_system_off...
NRF51822 most time is in sleep mode.
Each 5 seconds it wakes up to make ADC measurements.
But adc_event_handler force only once, but I want to see it every 5 seconds.
...
I'm new to using the RTT Viewer. It was working fine (all morning). I've only been using the SEGGER_RTT_printf(0, "string %d \n",x); call to dump text and data to the viewer...
Hi,
We are using the BLE keyboard example as a basis for a design and notice strange behavior.
Only change was to create a custom_board.h header for a button press on...
Hi,
I can use the DFU bootloader via HCI/UART to update the application image.
Reference DFU init pakcet . The init packet contains a 4-byte value identifying the version...
I searched the database but did not find an answer to my question.
My environment is as follows:
Keil uVision v5.18a
Nordic SDK 11
nRF52 PCA10040
Softdevice S132
...
Hello,
I am trying to write data to flash. I did successful write data to flash, but I need delays between erases and writes. I tried to avoid the delays with the NRF_EVT_FLASH_OPERATION_SUCCESS...
Hello,
I am currently using Renesas RL78 BLE chip and the UAP & NAP address is as follows 42-00-DE.
Now, for better performance, I migrated to Nordic nRF51422 and am...
Hi all,
I have to transfer a lot of data over the UART channel, and run into some problems...
First problem was/is the UART FIFO Size.
There are three different defines...
Hi.
I'm currently working on hrs_scanner example and have a question.
I'm working on latest nrf5 sdk11.0
and hrs_scanner example is in the 'ble_peripheral/experimental_ble_app_multiactivity_beacon...
Hi, I'm using a nRF51422 with s310 sd on sdk 10.0.0 and I have two different behaviours that are cousing me some problems.
I'm testing it with a DK (board 10003) and a...
Hi
I use the softdevice s110 with a nRF51822
I am trying to update the characteristic value using a timer.
But i have gotten this error BLE_ERROR_INVALID_CONN_HANDLE when...
