Dear reader,
I am currently working on a project using the NRF54L15 MCU. There is plenty of documentation available for this component, and the reference circuitry for the...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
Hello,
I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
HI: D:\ncs\v3.0.0\nrf\samples\bluetooth\peripheral_uart Using the nrf54l15DK board can run peripheral_uart examples,connection is disconnected. However, when I use the nrf54l05...
Dear sir,
Can we use NRF51822 OR NRF52832 as a slave device .As our controller is STM32F407ZET6 and we did not want to change any firmware from our previous version except...
I am using Keil to compile code and program into nRF51822 chip. SoftDevice s130 is used. There are various types of nRF51822 chips - nRF51822_xxAA, nRF51822_xxAB and nRF51822_xxAC...
Hi,
I need to measure the frequency of a PWM signal with 50% duty cycle through one of the GPIO pins. The frequency of input PWM signal ranges between 100Hz to 1000Hz....
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hello.
I use nRF52 , PCA10040 , S132 & SDK 11.
I want to send data what get through UART to nRF52 from a peripheral, to PC by UART.
Due to, I made this program from example...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
is it possible to configure the nRF51822 Beacon (RCA20006), that it could be used as a wifi access nfc device.
So that the device (Beacon) sends the Wifi SSID and...
Where can I find a working application that has an observer callback function (not a beacon) .
this application must have also the broadcaster callback function.
OS: Ubuntu 14.04
IDE: Eclipse, installed as per tutorial.
Board: pca10040
When trying to debug esb prx and esb low power trx I get the following error:
No source...
So I'm only use to programing PICs with mplabX
I've designed my board and am ready to dive into programing the Nrf51822
I'm a little overwhelmed by the different information...
Hello,
I have build a gatt server device and my application is setup following the tutorials, which are really helpful by the way.
Now I want to check if the notifications...
I'm doing a more complex application than what I'm showing here, but I've reduced it to the minimum. I'm initializing the RTC subsystem, creating a timer, and starting that...
Hi all:
I use the softdevice 2.0.0 and compile bootloader example with "dual bank" on the nrf52 DK,
Running a system that can using DFU from app then jump to bootloader...