Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Assuming that all peripherals that require the high frequency clock are disabled / turned off / stopped, how long does the HFINT oscillator run after calling __WFI()?
And...
What's the delay from setting the Start / Stop task in an RTC module to when the RTC actually starts or stops? Is it less than 1 clock cycle on the CPU (15ns)? More than one...
Hi, I am using the nrf52 dk to sample two analog inputs through PPI.
My question is if I can use different bit resolutions for each analog input?
-Erblin
Hello !
I have a problem with my program (on a nRF52 board) : when I send a value to the board via BLE, it seems that my static variables are reset.
I noticed that, because...
I need to store data in some moments and if something happen i have to read those data, i have to do a log events.
I use nrf51-dk and soft device s130. This data is taken...
"....\dfu_public_key.c(20): error: #35: #error directive: "Debug public key not valid for production. Please see github.com/NordicSemiconducto.. . to generate it.
i found...
nrf51 dk with 51422 device (10028) was running in Segger Embedded Studio example imported from IAR / Keil ble_app_cscs_pca10028_s130 SDK12.1.0 was just fine. I loaded couple...
Hi,
I'm new and I'm a student.
I have to connect the adxl345z to my board mb39c811-evbsk-02.
It has an nrf51822 integrated.
Someone can explain which pin of i2c/Gpio i...
We wanted to update the firmware over the air, We needed help for zip file creation(.dat file, .bin file and .json file). There are many links online, We needed an link which...
Hi,
I'm developing to NRF81522 mcu, using a softdevice S130.
The MCU is connected to another device through the UART peripheral.
I'm encountering the next problems...
Hi,
I am getting data from sensor and want to replace some new data with the older one in flash using fds. Right now,firstly i will write into flash by using one different...
I am using the nRF toolbox to upload bootloader and firmware to a hardware project. Our project requires the number of packets (found within settings > nRF toolbox > Number...
Hi,
I am trying to flash the blinky example from nRF5_SDK_12.0.0_12f24da, the program compiles and is also downloaded to the NRF52 DK successfully. But the LEDs are not...
Hello.
I´ve got problems with a via BLE connected IMU and data transfer over UART.
I´ve now tried several methods to implement UART connection but with the given baudrate...
