Hi,
We are currently migrating our project from nRF52840 to nRF54L10 using the nRF Connect SDK , and we have a few questions regarding MCUboot DFU using external flash ...
Are there any specific points using the external flash of a Thingy:91X?
I tried to adapt the "nrf/samples/cellular/modem_trace_flash" by adding an overlay copied and modified...
Hello,
I am using the same hardware, and firmware on 4 custom boards of the same device. I observed that I am getting different current consumptions in each devices.
I...
I’m working with a device that communicates over single-wire UART (half-duplex), where TX and RX share the same line (because the peer device is designed that way). Now I...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
I am planning on using:
NRGF51822 CDAB WCSP (= 128KB Flash, 16KB RAM, 3.5x3.5mm)
Another main chip I will be using is:
LSM303AGR ( www.st.com/.../en.DM00177685.pdf)
...
Hi
In my application I have a function that takes about 1 ms, in which timing is critial.
(I cannot allow even a few us change of the timing inside this function).
When...
Greetings, and thank you ahead of time to anyone willing to lend some advice.
I'm implementing application-layer security by requiring central devices to supply a user...
Hi,
I am having some trouble getting the nrf51422 (running the s130 soft device) to wake up after entering sleep mode. I have successfully entered sleep mode using NRF_POWER...
Hi,
I am trying to work with ble_radio_notification.h. When I import this file to my main.c, I have "No such file or directory error". When I try to add it to nRF_BLE folder...
Hii every one,
We are working on a project where we are using a temperature sensor LMT01, its giving a pulse output the pulse out is from 220mV to 600m. So I'm using lpcomp...
Hi,
I am getting only two values on startup and the remaining values as zero when using app_timer_cnt_get.
EDIT: updated entire main.c file
#include <stdint.h>
#include...
I am trying to bring the pc-ble-driver code up on a single processor ARM based board with Linux build under Yocto control. The boost library version being used is 1.60.
...
Hi All,
I'm implementing system clock using approach similar to
devzone.nordicsemi.com/.../
The idea:
NRF_RTC_EVENT_COMPARE_0 -> PPI -> NRF_TIMER_TASK_COUNT
...
I have a nRF51822 custom board for BLE UART application. Connects this to serial port of an ARM SoC board.
P0.09 is for UART_Tx and P0.11 is for UART_Rx. No RTS and CTS are...
i am using a blend micro with nRF8001. and i am using it as a hub in my project.Now i am getting a range of 13 meters.but that is not enough for my project.so can i increase...
Hi!
I'm using the nRF Sniffer software (Windows 1.0.1 Rel.1111) with nRF51-DK Board (Rev. 1.1.0) and Wireshark (1.12.5).
Everything works fine until the number of 65535...
hi
i work in sdk v6.1 and work with dfu over air and it work fine on s110 but now i open this project
nrf51_sdk_v6_1_0_b2ec2e6\nrf51422\Board\nrf6310\s310\ble_ant_app_hrm...
Hi!
Turns out that there is no need for the SD310 and the nRF bootloader. Which means that the flash layout is edited and current support for the BLE OTA is dropped since...
