Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
I am working in a custom board which is having nrf1822 chip and I am using Softdevice s130 2.0.1 , SDK 11.0.0, RAM available is 16Kb where soft device uses 5kb of RAM,heap...
I am duty-cycling the radio, so I listen with a timeout and then power off the radio (or transmit) if no packets were received. Currently I am ignoring the address event from...
Hi,
I have programmed s212 soft device onto to NRF52 DK and also programmed ant_broadcast\tx application onto the NRF52 DK. The LED is glowing to indicate that TX is happening...
What is the maximum input voltage for the ADC on the NRF52. I found answer for the NRF51 but nothing definitive on the NRF52.
I have a photocell (or LDR) to sense light ...
Hello,
I am trying to make a basic uart communication between my nordic NRF52 dev board (PCA10040, s132) and my STM32f429ZIT6 discovery board.
NRF52 : I used the example...
Dear Sir,
I and new of development nRF51(256K/16K), I read some sdk docs, but need further information and help.
Would like to save some application information...
Hi,
I'm trying to use the same timeout_handler for two different timers. I use the p_context (as explained here ) to pass a flag to the timeout handler, so that he knows...
At the start of programm, I create a timer_id used the follow code:
app_timer_create(&m_sec_req_timer_id,APP_TIMER_MODE_SINGLE_SHOT,sec_req_timeout_handler);
when the...
Hi, I started using the nRF51422 kit today. Downloaded nRFgo Studio, Master Control Panel, nRF Connect, BLE Sniffer, Wireshark 1.10 (after figuring out that you don't support...
Hai
i am planning to make an iot project with ble for my academics. I am using arduino to control the ble.
I was done a test with blend micro to know its maximum range...
Hello I would like to use more dongles with pc-ble-driver-py. For example I want to create multiple advertisers and test that my DUT would see multiple advertisers. I tried...
Hi all,
I was looking into using a PWM for LED dimming, and in an attempt to smooth out transitions between light states, I found that there was visible flicker as the...
Hi
I want to ask what the this define
#define NRF_CLOCK_LFCLKSRC {.source = NRF_CLOCK_LF_SRC_XTAL, \
.rc_ctiv = 0, \
.rc_temp_ctiv = 0, \
.xtal_accuracy = NRF_CLOCK_LF_XTAL_ACCURACY_20_PPM...
Our code is 21k excluding soft-device,as per the example 15k should be the max size limit of code to update FOTA. Is it possible to make changes in DFU bootloader so that...
I read the doc of nRF51, so many reference pic.
Can anybody have make a summary of it
I think Decentralized understanding is difficult.
If we can read all of it in...
