I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I tried if there is a possibility that my device would brick if I interrupt the DFU process. notice that I'm using SDK10 with dual bank bootloader. I uploaded the app over...
I am going to develop on nrf51822 and the data sheet says nrf51822 is s110.
I want to load an example of sdk 11 but there is no example for s110.
I am a total newbie, so...
On the nRF52, does the TASKS_HFCLKSTART need to be trigger again after waking up from sleep, if the the HFXO was started before going to sleep? Or does the Clock control circuitry...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I have one characteristic which send data with indications, for each frame sent I wait for acknowledgement on case BLE_GATTS_EVT_HVC : before sending the next data
but...
I write a source code to test led and button driver. it's work with a loop but when add sd_app_evt_wait() to use low power mode of nRF52.
I suppose that I forgot something...
Hello,
i have one problem.i am working on the TWI using Handler.it is working.
but i have very strange issue regarding to the dereference the value.
please check in...
Hi,
I am facing some issue while working with both GPIOTE and SAADC. I have merged the GPIOTE and SAADC sample example sdk code into a new project but what I am facing is...
Hi,
I am using BSP for button detect. I wish to read the button Long Press of Different intervals. 3 Secs, 5 Secs etc.
Someone please help me achieving this. Some code...
According to the documentation in infocenter there should be three soft devices for the nRF52832: 132, S212, S332. I downloaded the nRF5 SDK and I can only find the hex file...
Hi all,
Does anyone know the dimensions of the NRF51 dongle? I'm seeing 16mm x 28mm here but that doesn't seem right (might be the dimensions without the USB connector...
Hi,
Can any one suggest me how to program SoftDevice and Application program to nRF51288 BLE Motherboard using Keil 5? Please specify how much IROM1 and IRAM1 allocation...
I've studied the nRF OpenMesh for a couple of days, and could run the BLE_Gateway example among serval nRF51DK boards.
But now, I still don't have any feeling/concept about...
