Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
after successfully calling sd_softdevice_enable(), I call ble_cscs_init() and that function returns with error code 7, which means NRF_ERROR_INVALID_PARAM. I've tracked...
Hi,
After doing an sd_nvic_SystemReset(), the bootloader does start advertising, but for some reason the android app nRF Master Control cannot connect to it.
If I connect...
Hi everybody,
I'm currently writing an Android application allowing me to communicate with a NRF51422.
I've created on the Nordic chip one proprietary service with 2...
please help to confirm the ESD grade of nordic SOC. i can't find all the parameters(HBM, CDM,MM) in the datasheet, only HBM in 24LE1, and only HBM&CDM in nRF51822.
I'm trying the ble_app_hrs example on a custom nRF51822 board with s110 6.0.0 softdevice.
Debugging in Keil, the firmware runs fine up to ble_stack_init(). Within ble_stack_init...
Hi All!
In all exsamples in function "ble_evt_dispatch" we have different order to call sub functions.
Most functions to call is:
dm_ble_evt_handler (device manager...
I'm testing a data collecting program which samples data every 2s and reports it through UART ( printf("data=%d\r\n", data) ) on a PCA10001 board. I found this program may...
Hello,
Got a question about nRF51422 and S310 stack. I am trying to understand how the radio is being handled and how the softdevice handles events in a specific case....
I tried communication between PC and my own board(nRF51822) PCA10000 usb dongle&MCP, I found that the first time I send n(where n is any decimal number) bytes data(s) from...
Dear Nordic guy,I'm developing with nrf51822 (6.0 stack binary and 5.0 SDK).
I recently updated the code and stack binary(6.0 stack binary and 5.0 SDK).
My function is not...
static conn_mw_handler_t conn_mw_handler_get (uint8_t opcode)
Inside the function,
for (i = 0; i <conn_mw_item_len; i ++)
{
if (opcode == conn_mw_item [i] .opcode...
It seems like it should be easy, but I've spent a fair amount of time and haven't found a way. I only see options 5.0.0 and 5.1.0. There are also links to earlier SDK versions...
