I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi (I'm new at this, sorry for my question)
About Gazell & Pipe (nRF24LE1)
What is the utility of 6 or 8 pipe, whether only has 3 RX_FIFO for working simultaneous?
Can...
Hi All
I am trying to verify UART on one of our custom boards having nrf51822.
We have only one uart which we are using to forward the data received over BLE.
I am...
I use the demo : ble_app_proximity
to connect with android app
In android use this :
mBluetoothGatt = device.connectGatt(mContext, true, mGattCallback);
to set the reconnect...
Hi,
I'm checking out the new nrf51_sdk_v6_0_0_43681 for S110-SD-v7
Is there a revision-history available for the src files within the new SDK package?
For example...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Hi all,
I have been stuck trying to debug the example project for a couple of days now and could not find the answer through searching. Here are my problems.
Background...
Hi All
I have a bunch of nrf51x22 (4,8) and I'd like them to read their own firmware data and send this to others that are in DFU mode using the over the air (OTA) method...
Dear Nordic Developer Zone,
I'm using nrf51822 EK testing the GPIO sense function. The code I'm using is based on what a nordic employee has posted elsewhere in this dev...
hello,
i was trying to compile the softdevice s130 example code given with softdevice download from nordic.
I am using the ARM-MDK lite 4.74 version. It is showing error...
My design goal is to conserve as much battery power as possible on a device that typically gathers data 30 to 40 minutes per day. To that end, our thought was to make the...
hi~
6.2.1
Updated Setup_JLinkARM_V490e to Setup_JLink_V492
Updated nrfjprog to version 5.2.0 (see own release notes for changes)
where is release note ??
i can...
Dear all:
I want to constantly transmit messages from a nRF51422 to an other nRF51422 with specific ID by ANT protocol. Then, I want to receive the messages from one to...
Hi,
I want to build a Tx that can reconfigure a channel(like change the device's number) after finding out a long time failed to send message.I use the way below:
sd_ant_channel_close...
hiii...
i hv made a custom profile with concurrent broadcast feature tested in master control panel and some other phone app... working properly.. but wen i tried in iphone...
