The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
I am trying the IOS app and I tried to set the alarm on the "out of range" event with the beacon
It doesn't fire the alarm although I am trying an Android phone with same...
I am trying to run the debug project for ble_app_hrs following the steps in "nAN-29 nRF51 Development with GCC and Eclipse Application Note v1.1.pdf"
but I get this error...
Given that most of the SDK (including the softdevice hex) is public now due to the mbed support: would it be possible to open up the downloads for the standard nRF51 SDK and...
From the s130 release notes:
GAP
Concurrent Central, Peripheral,
Broadcaster and Observer operation
(DRGN-4354).
Up to 4 simultaneous
active connections...
Hi.
I am trying to modify the bootloader example provided by nordic.
I am able to compile/link my code and use nRFgo studio to run it, but for some reason I can not debug...
Hello,
i´m using nRF51822 with S110 SoftDevice to transfer data from Sensors that will be read out via I2C by the Nrf51822.
I have read some topics about how it is not...
Hi,
I bought nordic evaluation board 2 days ago. I have been searching through the forums to enable and test the voltage level of a battery and monitor it via UART. After...
Hello all,
Is it possible for a nRF51822 to read information from another peripheral Device using broadcasts or advertisments?
I have an application where I need to...
hi,
I have been reading some posts regarding similar issues, but I am not able to nail down this one.
I am trying to create a custom 128 UUID and associate some Service...
I overwrited the application program which made with v5.1.0 and it included only difference against the v5.1.0 to sdk v6.1.0. After this, I buidled it but the target didn...
I am looking for a dev kit which would allow me to try out SoftDevice S130, will I be able to use S130 if I buy any of these:
nRF51822-mKIT
nRF51822 DK
nRF51822 EK...
The nrf51 reference manual shows timing diagrams for the TWI interface when reading from slaves to have a shortcut between BB and SUSPEND. My assumption would be that's there...
I am using the ble_app_uart code from SDK 6.0 on my custom PCB with a nrf51822. I am comparing it's functionality with a PCA10004. Both are running the exact same code. I...
Hi all,
some time ago we bought a nRF51822 Evaluation Kit with the PCA10001 being Version v2.0.0.
Why exactly is it not recommended to work with the new SDKs such as SDK6...
Has anyone played with getting the iBeacon reference kit/software to run with the SD7.0 code?
I'm wanting to change from the boot loader + SD 6 + app to a simpler SD 7...
