Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Hi,
I have a Question regarding one project in which 1 NRF24L01+ Module transmit to multiple devices at the same time ? How we can configure for multi transmit ? like Tranmitting...
Dear Nordic,
The guys at ARM have this community around mbed which looks great. I would like to use it, but before I do, I would like to check if their use of your (source...
Hello,
I'm trying to understand how the ble_app_hids_keyboard example works. So far, I have hooked up a few more buttons to the board and can type hello.
Now, I would...
Hi all,
In my project I'd like to use gazell for to communicate 2-6 devices with host.
Furthermore I use switching between BLE and Gazell (only 1 device support till now...
I am trying to port an application from MBED LPC1768 to a nRF51822 Evaluation board to develop a multi-function application for the nRF51822. The BLE part (developed on the...
I am hoping to develop a device that works as a remote control for a smart phone app. There will be at least 5 buttons, and as the button presses will be infrequent, I am...
Hi
How to start and stop scanning continuously in android devices ?.I found that In Nrf master control panel android app there is an option of performing scanning such...
Hi,
I downloaded and installed latest master control panel for Win7. It now crashes when communicating with nrf51 dongle. Seemed like it crashed the first time while it...
I'm using the APP_BUTTON_INIT-Function to register a button at the GPIOTE-System. This works great while running normally, e.g. I can react on debounced button_down or button_release...
Hi
I am developing for the nRF51822 a 4 layer print with a power and a ground plane in the inner layers. I will be using a balun from Johanson Technology (2450BM14E0003...
I've heard that's not allowed. If so, why?
If it is allowed, are there any precautionary steps I need to take, not to interfere with the radio?
Thank you!
Gil
...
Hello, we have a custom board based on the CEAA WLCSP reference schematic with internal LDO setup. Our supply voltage is 1.8V (VCC_nRF). Unfortunately we don't see any BLE...
Hi,
We are planning to use the SWD Tag Connector with our nRF51822 platform.
Please refer the snapshot for pin 3 connection on our board with Tag connect footprint.
Pin...
Hi
My product is ready for mass production, before start to sell, we need to do the Bluetooth qualification, we asked several local test labs, they told us that their test...
