Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Am I right in thinking that the button handler only causes an event for a button press(although I realize it is possible to configure the button such that a release is interpreted...
Hi,
I have a Question regarding one project in which 1 NRF24L01+ Module transmit to multiple devices at the same time ? How we can configure for multi transmit ? like Tranmitting...
Dear Nordic,
The guys at ARM have this community around mbed which looks great. I would like to use it, but before I do, I would like to check if their use of your (source...
Hello,
I'm trying to understand how the ble_app_hids_keyboard example works. So far, I have hooked up a few more buttons to the board and can type hello.
Now, I would...
Hi all,
In my project I'd like to use gazell for to communicate 2-6 devices with host.
Furthermore I use switching between BLE and Gazell (only 1 device support till now...
I am trying to port an application from MBED LPC1768 to a nRF51822 Evaluation board to develop a multi-function application for the nRF51822. The BLE part (developed on the...
I am hoping to develop a device that works as a remote control for a smart phone app. There will be at least 5 buttons, and as the button presses will be infrequent, I am...
Hi
How to start and stop scanning continuously in android devices ?.I found that In Nrf master control panel android app there is an option of performing scanning such...
Hi,
I downloaded and installed latest master control panel for Win7. It now crashes when communicating with nrf51 dongle. Seemed like it crashed the first time while it...
I'm using the APP_BUTTON_INIT-Function to register a button at the GPIOTE-System. This works great while running normally, e.g. I can react on debounced button_down or button_release...
Hi
I am developing for the nRF51822 a 4 layer print with a power and a ground plane in the inner layers. I will be using a balun from Johanson Technology (2450BM14E0003...
I've heard that's not allowed. If so, why?
If it is allowed, are there any precautionary steps I need to take, not to interfere with the radio?
Thank you!
Gil
...
Hello, we have a custom board based on the CEAA WLCSP reference schematic with internal LDO setup. Our supply voltage is 1.8V (VCC_nRF). Unfortunately we don't see any BLE...
Hi,
We are planning to use the SWD Tag Connector with our nRF51822 platform.
Please refer the snapshot for pin 3 connection on our board with Tag connect footprint.
Pin...
