Hi, i have locked my beacon with the write_lock characteristic and now i want to unlock the beacon with the lock code which is hard coded in my code. but i was unable to do...
Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello,
I can see s110 api commands as a web pages on infocenter.nordicsemi.com .
Is it an api list of commands manual in a document like pdf, etc.?
Thanks.
We are trying to configure the I2S peripheral for working with the ICS-43434 microphone ( www.invensense.com/.../) , but we are having a hard time fulfill the requirements...
The product spec is not clear, what is the maximum current draw possible from a 52832? Please assume ALL features are in use and fully enabled.
Thanks.
Hi Dev Zone,
I am going to communicate my nRF52840 Preview DK with an arduino shield. I am checking the PIN number. According to the information about the Arduino board...
Hello, I want to switch the functions between beacon advertising to connectable advertising.
In the code , it can be initial as a beacon advertising or normal advertising...
Hi,
I am running the ble_app_beacon example in nRF52 DK (PCA10040). I can see the nRF beacon in nRFConnect app - but not in the nRFToolbox - Beacons. After opening the app...
Hello,
I am using WT51822-S4AT based on the nRF51822 SoC and I am trying to program it with the ble-beacon example from the SDK. Looking at the DK documentation, I need...
Hi,
Device- nRF52832 (nRF52 DK)
SDK version 14.2
SoftDevice version 5
Segger embedded studio.
I am trying get the BLE working, unfortunately calling nrf_sdh_enable_request...
Hi, Everyone How to turn on 4 LEDs in BLE ? I am testing ble_app_uart on nrf52832 (softdevice s132). Try to blink the four LEDs on the board do. I have added to main() bsp_board_led_invert...
Hi,
I want to create a custom GATT service. So I duplicate the example from the SDK ble_app_blinky. Basically what I did so far is rename all the "LBS" (ble_lbs, lbs_p,...
Hello, I am trying to store microphone data from the Nordic Thingy by modifying the Nordic Thingy Android app .
The Thingy firmware encodes the digital microphone data...
Hi there,
First of all, I'm pretty new to this, so next question might be obvious to others.
I try to decipher a line of code, and the little Part is what puzzles me...
I've created 2 custom PCB boards, 1 main board and 1 dongle based on the nF51822. The Dongle board uses the default ble_app_uart_c code. The main board transmits to the Dongle...
