hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello
There seems to be no makefile in this example to use with armgcc compiler(why?) so Im trying to port it using the makefile from the ble_app_att_mtu_throughput example...
How to write driver for ADC by accessing direct registers of nRF52840 ?
I don't wanna use SDK APIs.
I wanna read LDR value connected to A0 (PO.3) pin in continous mode...
Dear all,
I'm trying to change the advertised device name during advertising depending on some variables.
I'm observing with nRF Connect and Lightblue, both running on...
Hi,
I have followed the steps for the 2 demos for nRF52840 DK, the Heart Rate and the Proximity demo. In both cases, when disconnected from the android device, the evaluation...
Heey everyone,
I'm currently working on a wireless application and we would like to have a range of atleast 300 meter. Yesterday I was testing the range between 2 SDK...
I work with Kenkou GmbH in Berlin. We are looking for Firmware Developers and Engineers with Mid - Senior experience to support our project. We are hoping to extend the visibility...
Hi All, Nordic,
In my application, I don't always need BLE connectivity, so I was hoping to disable the S132 softdevice when not needed. However when I do this FreeRTOS...
Hi,
I am working on a project with BLE and TWI module. With some help, I manage to set a TWI communication ( https://devzone.nordicsemi.com/f/nordic-q-a/29371/twi-issue...
Every once in a while I will get a failure that results in the app_error_fault_hanlder() being called and the following info:
ID = 1
PC = 0x14550
error_code = 0x495...
Hi, I use ble sniffer 2.0 beta with nrf51 (pca_10031_51296aa.hex). Is there a sniffer api documentation with description of the UART protocol (as with sniffer 1.0.1)?
Good morning everyone,
I am facing a weird problem concerning the use of the UART service.
I am currently using the NRF52832DK to develop an application. In a nutshell...
Hi Forum,
I am working on nRF52840 THREAD sleepy node and facing an issue in deep sleep mode. The current consumption in deep sleep mode is more-around 60-70 micro Amp...
Hello guys!
Are there any difference in using FDS library with a nRF52832 or with nRF52810?
I will explain.
I'm using a FDS for writing/reading to flash for 2 months...
