Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
Hi,
I noticed that my current NRF52 based prototype is consuming 4.5mA as soon as I enable the BLE functionality, when its off its only 1.6mA
I send the chip to a sleep...
Hello !
I was wondering How the interval connection was calculated in the Android application nRF Connect ?
Do you use a special/ hided function ?
I tried to get it...
Hello,
I want to set up client and 3 servers which will send data from sensors to client with high data rate. Currently I am testing light switch example from Mesh SDK 1...
Hi,
I am using nrf51822 with SDK 12.2.0. As of now, we are using RL-51822-A1 for beacon as well as scanner.
But, we are not getting stable pattern for RSSI at 2m, 4m and...
Good day!
I am working on a custom board which has NRF52 and am using SDK 12.2.0 and in that, I want to stream BNO055 data. The base code I'm using is ble_app_hrs. The problem...
I want to set gpio using one interrupt and want to clear it using another interrupt funtion?
It seems i can only use the toggle funtion ,if i use the nrf_drv_gpiote_out_set...
Problem Statement: For one of our requirement we have to switch tx power in steps in ascending order continuously.
We are using ble_radio_notification feature to achieve...
Hi,
I'm trying to receive sensors data from three fdc1004 that have the same address. Can you have three TWI interfaces at the same time? How do you modify the nfr_drv_twi...
Hello,
I've just started using Segger Embedded Studio v3.30 for my development and I've been having trouble setting it up. I followed the instructions in this blog but...
Hi, I am programming on Thingy 52 to try to get it work like one of my nRF 52840 DK. Basically, I want Thingy to send beacons with data periodically and another Thingy to...
I have followed the tutorial given in the Nordic Devzone for using eclipse and haven't faced any problems while compiling and uploading the example "blinky".
I made sure...
Hi, ,
I am working on the nrf52832 development kit and want to program it as an I2C master. I have download the nRF SDK v12.3 but I am unable to understand the code written...
Hi guys
I am wondering what could be better for my system:
Multiples nRF52 central and peripherals (uart input/uart output to simulate keyboard and display)
SDK 13 ...
HI,
We use nrf52832 on a device with sdk 14.1.
Our product has to work at different temperature (between 20 and 70°C).
We did some measure and found this :
...
Hi, I have met an issue that the "ANT_CONFIG_TOTAL_CHANNELS_ALLOCATED" can't set more than 15 in ant_multi_channels example. Now I have a project that it need receive 100...
