Hello, I'm working on my Senior project for school and it involves me creating a PCB that will be utilizing the NPM1300_QEAA. Is there a footprint model for it in Altium,...
Hi,
Now, I'm doing a project. A device node sends picture data and the other one receives these data. Then the receiver shows the picture on the SSD1306 display.
At receiver...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Hi, I am new to Dev Zone. I am writing debounce logic and I am wondering if a button can have an interrupt set when the GPIOTE sense a HITOLO transition to fire the first...
Hello, I'm currently developing BLE_SCANNER(GATEWAY) for asset tracking or management.
My scan environment is,
[Our device -- same UUID]
The number of our beacons...
Hello. I have the same problem with https://devzone.nordicsemi.com/f/nordic-q-a/54373/uart-logging-backend-hangs-in-nrf_bootloader_app_start/220132
But this thread was stuck...
I'm trying to register a handler to determine when a system event occurs?
Previously on older design kits, I used softdevice_sys_evt_handler_set(......) to register the...
Hi,
I've managed to code an app for nRF52382 (S132, SDK14) which works properly. Also, I've taken "bootloader_secure_serial" and removed a lot of stuff to code a simple...
To the kind attention of Nordic support team,
I've just downloaded a fresh copy of nRF5_SDK_16.0.0_98a08e2.zip.
I would like to download code in nRF52810. The code in...
I want to make a programmer for nrf52832. Do you know where is the documentation of SWD is ?
Note: I found the similar question, but the links are not active
Hi
I am using Segger Embedded Studio and SDK_v15.3.0. I have a C++ code that I wish to run on the board. It has a lot of printfs. I want to see the output of the print statements...
Hi,
I'm new to Nordic Semi chips (nrf52840) and need to use TWI as a master to connect to two sensors. But I'm a bit confused about the different drivers: TWI and TWIM....
Hello to all,
I have a problem related to the client side Global Attribute: I have implemented an "On / Off Switch" that presents the cluster On / Off (0x0006), client side...
Hello,
When we analyzing the traffic of our application (many thanks to the team developing the sniffer), we have several questions about sending write confirmation.
for...
We do have a product in which we program a bootloader on the target. It is remotely based on the ble_app_buttonless_dfu example. The bootloader is not actually used in the...
Hi I am building a software watchdog to monitor nrf52 peripheral states to have higher confidence for 10+ years battery lifetime. The idea is to check every few seconds if...
I am working with the S140 softdevice v6.1.0. The message sequence charts located on the Nordic infocenter are great help. Question: are they available in a printable form...
Hi,
Is there any editable software available that I can use to create a custom interface between my PC and my nrF58210 module. I have been successfully using the Nordic...