Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
Hi everyone,
I am testing the NRF9160 DK and I want to test the low power mode.
I found and tried the solution detailled in this blog about how to measure PSM idle current...
Hi,
I am using nrf52840 controller . I need to transfer the data using Bluetooth at 10ms by using application timer and i am using SDK 15.3 version and soft device S140...
Hello, i have question: How nRF Connect SDK gets MAC addresses Steps: 1. I build android ble peripheral app and starting advertaising. When i did it, MAC address alwalse random...
Hi,
Greetings!
I am using below setup
nRF52832
Mesh SDK 4.0.0
SDK 16.0.0
Application Example: light_switch_client_nrf52832_xxAA_s132_7.0.1
Issue:
Using above...
Hello,
I am referring to this webpage https://github.com/bjornspockeli/custom_ble_service_example "Custom Service Tutorial", I followed all the steps mentioned on the webpage...
I started developing a beacon app and used BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED advertising type. I then changed the type to BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
pc-ble-driver compile on macOS
I am trying to compile pc-ble-driver on macOS 10.15.2 by following the very excellent instructions on the github page.
Fixing GCC issues...
Hello,
I have set the device advertising as follows:
Advertising name is getting broadcasted with a full name until it gets changed and to 4 letters device name. In...
We have our SCL line on P0.10 (NFC2) and SDA P0.23
When I try to start a I2C transaction nothing happens, and NRF_TWIM0->TXD.AMOUNT = 0. I have verified that SDA/SCL are...
Hi,
I tried to implement a unprovision method for provisioned devices such as light bulbs. By simply on off it several times. And saving state into flash.
Currently I...
Hi Nordic Team,
Please share logic to de-initialize the advertising functionality of peripheral devices after the peripheral device stops advertising without any memory...
Hi Nordic Team,
In my BLE project, first the central device starts scanning, then the peripheral device starts advertising, the peripheral device gets connected to central...
HI,
I got nrfutil + BLE DFU app update working using the ble_app_hrs for the test. I am using the nrf52DK + SES for development, and I have also an external nrf52832...
Hi
I'm using this simple_pwm code to drive my speaker, I use this as a buzzer but I want to change the frequency.
In this code ".base_clock = NRF_PWM_CLK_125kHz", the...
