Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello,
I have a custom nrf5340 board with an attached external RAM on the QSPI (I understand only NOR flash ICs are supported) on the older version of the SDK such as...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
I have a custom board using a nRF52840.
A part of the configuration is a Analog Devices MAX98357AEWL+T Class D amplifier which is driven by i2s0.
When the board is idle...
Hi,
When running the python script in attachments
By invoking it like this :
python.exe ./nrf_build.py --sdk-version v3.0.2 --project-path <path_of_the_project...
Dear All,
any opinion on attached antenna design (blue) to the outside of a metal housing?
PCB that flows around an aluminium die cast housing
External to aluminium...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hi all,
I cannot find the exact connector to use for the P19 Debug out header on the pca10028 board.
The one I have has the plastic around too big so it doesn't fit.
...
Hi,
I'm working on a simple ADC application where I sample using analog channel 1 and then read the value through the debugger. However my results are nonsense. I have...
I'm using s120_nrf51_ble_driver on PC.
To connect the BLE dongle, we need to COM port number to be known (parameter of sd_rpc_serial_port_name_set). Is there really no...
I am working on a project on wireless interface between phone and SIM card. I want to use chip nRF51822-CEAA to run SIM card simulation at phone side (include wireless communication...
in nRF51822 product specification a maximum absolute rating of 3.9 Volt is reported, while in electrical specification the maximum voltage is 3.6 Volt.
The question is :...
Hi,
I have tried with the nrfjprog tool and I get the following error:
Command:
nrfjprog.exe --eraseall --programs s110_nrf51822_7.1.0_softdevice.hex --program HILO_P_01...
Am trying to setup a module where I need to send the Serial port ( say from printer/peripheral COM)
to a BLE Peripheral/Central Module. Not sure which SOC or combination...
I have a board built which is a tracking device with a GPS and GSM modem. I'm beginning field testing and have been flashing it with a Segger then disconnecting the Segger...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I have used the nrf8002 chip before and love it but now I am trying a different application that requires a bit more smarts. I am trying to design a system that can have an...
I have an nRF51822 board that is running fine for a while. At some point, it runs into an error and calls ble_debug_assert_handler() and goes into an infinite loop. At that...
Hi all,
I am new to nRF51822,now I want to used a simple ble application to send a data,and nRF51822 ble device read this data to control RC servo motor ,for example app...
