Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
Hi all,
I'm trying to characterize the UDP throughput of a Thread network consisting of nRF5340 DK devices. I saw that Espressif made a test report and they seemed to use...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Dear Nordic:
I have transplanted my code from sdk 10.0(nrf51422+S310) to sdk 13.1(nrf52832 + s332(v4.0.2)).
I program softdevice and application to my board by nRFgo_Studio...
I just tried to add a custom service, so I expanded my ble_cfg.gatts_cfg.attr_tab_size.attr_tab_size. Now, when I call sd_ble_cfg_set(BLE_GATTS_CFG_ATTR_TAB_SIZE, &ble_cfg...
Hi everyone,
For my project I'm currently using the sdk 10.0.0 (S310 on a nRF51422) and I would like to use the Secure DFU provide by the sdk 12.0.x.
Working on a nRF51422...
Hi everyone
We have a custom made board with NRF52832 chip. We are send it to FCC test lab and they told us the occupied bandwidth (OBW) is too small, 940kHz less than...
Hello,
has anyone tried new v1.1.0 for nRF6707? If I change the window size to more than original 2.0s, GUI becomes very laggy and it is very hard to stop the recording ...
Hello,
I've been trying to test DFU over UART which has been added in SDK13.1 but after following every resource I've found I always end up with DFU not working
The...
I found this question which partially answered what I am looking for:
devzone.nordicsemi.com/.../
Essentially, if I am creating a new project with my main.c file and...
Hi I am trying to design a custom BLE board using NRF52832 by following the reference layout.
I am new to RF design and I have got a few questions that I would really appreciate...
Hi
I'm trying to implement DFU in my project. So far, after I sending 01-04 to the control point characteristic(1531)，I can get bootloader signal, to be exactly, i can enter...
Hi,
Can we interface a smbus based sensor with NRF51 or NRF52? The only difference between smbus and TWI is the minimum speed requirement which is 10Khz if I am correct...
Dearl all,
I want use the eclipse and gcc together to program the board nRF52840 Preview DK. I was following the tutorial devzone.nordicsemi.com/.../.
I followed the...
Hi,
I'm using nRF52832 with sdk 13.0.0(softdevice 4.0.2).
I had trouble to connect nRF52 and some android 7.0(or upper version) smart device.
I tested samsung galaxy tap...
Hi All,
I am trying to get the serial DFU working with nRF52832 development kit with SDK 13. I am able to get the bootloader flashed and have installed the nrfUtil tool...
since im working on sdk9... advertising program(hello world).i wanted to generate a random address .but i couldnot complete it sucessfully.can you please help me in providing...
