Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello,
I have a custom nrf5340 board with an attached external RAM on the QSPI (I understand only NOR flash ICs are supported) on the older version of the SDK such as...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
I have a custom board using a nRF52840.
A part of the configuration is a Analog Devices MAX98357AEWL+T Class D amplifier which is driven by i2s0.
When the board is idle...
Hi,
When running the python script in attachments
By invoking it like this :
python.exe ./nrf_build.py --sdk-version v3.0.2 --project-path <path_of_the_project...
LAST EDIT AT END OF POST
We are using a custom board with an nRF51822 programmed with a modified beacon application (which worked several months ago). After opening MCP...
Hi,
Everyone,
I am Using S130 and sdk 11.0.0.2-alpha with nRF51422 chip.
I have two crystal in my custom pcb,
one is 32 Khz crystal for LFCLK between XL1 and XL2 (pin...
My application is using the FIFO UART module to communicate with another MCU. It is also running softdevice S132 v2.0.0.
While most of the time everything runs smoothly...
Hi
Are there any major OSes/stacks (e.g. Linux, Android, iOS) that provide support for the L2CAP feature so that we can test our Nordic device against?
Thanks
Hi,
I would like to know what is wrong with my code, which is presened below. Each time the timer is triggered I would like that the program writes four bytes into the...
I have a project that requires a bluetooth central to be used to gather data from a HRM service, which shouldn't be too much of an issue. However, it also has to store this...
I have searched here for an answer to this, but cannot find exactly what I am looking for. I am trying to put my Rev3 51822 to sleep and wakeup via GPIO. When I enable GPIO...
Whats the best way to secure my advertising packets such that others cannot make sense out of it?
Do we encrypt the packet data so that it is gibberish, random and not...
Hi!
We're running a S130 Stack to act as both Peripheral & Central at the same time. Everything is working fine but i i'm not quite sure about best approach for handling...
Hey ,
My application stores the data on BLE disconnect to pstorage succesfully.
But on reset if i try to read the data from pstorage it stops advertising, but the pstorage_load...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0.
I am able to doing dfu of softdevice and bootloader individually but when i try dfu for combined (SD + BL) then...
I can't find nrf.exe in C:\Program Files (x86)\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf
I only find nrfutil.exe in that folder.
Shall I use nrfutil.exe...
Softdevices have several separate version number systems:
a) the human-readable release version - used for hex file naming.
e.g. s110_nrf51_8.0.0, s120_nrf51_2.0.0
b...
