I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
I am trying to use Eclipse+GCC for my projects. I found a similar issue as stated in the following post:
devzone.nordicsemi.com/.../nan-29-nrf51-sdk-no-project-files
...
I am having trouble getting up and running with the development kit (without the starter kit).
My setup is as follows:
The PCB antenna module is hooked up to the JTAG...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hello,
When the Ant stack want to transmit a packet while the BLE stack is using the radio, an event called EVENT_CHANNEL _COLLISION will be returned, is that...
Hello,
when the device NRF8001 starts Advertise, it sends out only one packet and unexpectedly terminates with a fatal hardware error in "ll_ctrl.s0.c" line 572. This happens...
Hi,
I'm trying to install Master Control Panel v.3.5.0 on Win7 64bit but I get the "Master Control Panel Setup Wizard Ended Prematurely" message. I have .NET Framework...
It would be very convenient to increase the output power of nRF51422/822/922 with at least 3-6 dB in order to get enough range. I'm currently not using nRF51422 for ANT, only...
with 1.16.0.3031 I cannot recover but I still can recover in Linux using a tweaked Makefile.posix
I don't remember this problem with previous version. Hence it must be...
I have tried to configure the nRF24A2 chipset in the asynchronous transmission mode by setting the bits in the extended field assignment. Unfortunately for some reason, it...
Hi,
I want to use 51822 to communication with 24l01,the 24l01 module is transmit temperature data, the 51822 is used to read the data from the 24l01.I set the parameters...
Hi,
I recently started on the nRF51822 Evaluation Kit and got the blinky code/example running. I then tried getting the Heart Rate application going but noticed when I...
Hi,
I want to use the nrf51822 to communicate withe the old module of 24l01p, in the module of 24l01p, the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch...
Hello,
I've been trying to get my TWI device working in conjunction with the BLE stack (i.e. s110 softdevice is enabled) on a nRF51822.
I found another thread with an...
Hi,
I want to use the 51822 to receive data that from the module of 24l01.the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch[2] = 0xe3;
addrofch[3] =...
