Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hello,
I face a problem which I can't understand really and where I need support.
It is strange...
In our electronics we use the nRF52840 which is enclosed in a module...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
Hi,
We are using Nrf51822 , pca1001 evaluation board.
when i flash bel_app_proximity code (by disabling led function in advertisement_star()),
current consumed by...
Hello Developers,
Just started with the nrf51822 and managed to install:Keil 5.05, Segger J-link, nRFgo Studio 1.16 and the Master Control panel. I also loaded the SoftDevice...
Hi,
I'm knowing the device_firmware_updates project in SDK and I want to know whether I need to program the softdevice when I do the device firmware updates over UART?...
I am developing a windows application, using the MasterEmulator api.
I am discovering BLE devices with scan parameter Active and Passive.
The result is that most of the...
HI,
when I used nRF51822 for 2.4G transfer ,I found that RX can't receive data in some direction .Can TX use two antennas and matching networks to work alternately in order...
Hi all,
I am currently working on a BLE project based on the PCA10001 evaluation board. I am trying to follow the nRF51 application note. I have done everything that the...
Hi
I'm using the nRF51822 and custom a service.I add 4 characteristic in the service and all of them
config to indication type to send data.Everything is Ok and sending...
Hi
I'm just starting with all this. My set up is a nRFgo motherboard with a nRF51422 DK attached (PCA10007).
I've installed all the tools of the toolchain as stated in...
I've just flashed the softdevice 5.2.1 and BLE Proximity sample app to my nRF51822. I presume any previous bond state on the device should have been wiped by doing this. ...
It would be nice if you could update Application Note 29 ("Development with GCC and Eclipse") for the nRF51822 to include instructions for Mac OS X.
I don't think it's...
Hello,
I developed a BLE based application using nRF51822 softdevice S110.
This application is very low consumption.
The device connects every 60 seconds, and can send...
I try SDK hid mouse example this days, In SDK v4.2.2 it does not work sometimes when I press button 0~3 ,and some times the mouse arrow move slowly when I press the button...
Hi,
I'm trying to make the nRF module work with an older IO demo board. Does the flexible GPIO system via pin crossbar allow you to modify the pin assignments of the SWDIO...
I what to send button data , how to construct button data array :
uint8_t buffer[INPUT_REP_BUTTONS_LEN]; in function ble_hids_inp_rep_send() ?
In SDK mouse demo I can...
