I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hi - I am completely lost and I'm really hoping someone can point me in the right direction. I'm simply trying to get started with the nRF51922 development kit and nRFgo Motherboard...
I opened both the NordicSemiDemo.xcodeproj and nRFDemo.xcodeproj in Xcode 5.0.2. When I try to run them (Product->Run), I get the splash screen in the simulator, but when...
this time i have some encryption related questions to ask.
I use the "BLE_GAP_CONN_SEC_MODE_SET_XXX" to enble link encryption, doese this correct?
can i set the encryption...
Quick question regarding the boot process of the nrf51822. If a bootloader address is written to 0x10001014, will the bootloader code always be executed, regardless of whether...
Hi
I am using ble_app_hrs for my application.
in this case ble has highest priority , next gpio then timer.
if i send continuous data over ble, by using function...
Hello Nordic expert,
In nRF51822_PS_v1_3, the max bit rates for SPI master is 8Mbps(section 8.8, page43).
But in nRF51822_PS_v2.0, the max bit rates for SPI master change...
I heared a rumour that the NRF581922 will be withdrawn and an other solution will become available. We have planned the 581922 for implementation and want te release the product...
/* YOUR_JOB: Use an appearance value matching the application's use case.
err_code = sd_ble_gap_appearance_set(BLE_APPEARANCE_);
APP_ERROR_CHECK(err_code); */
Shoult...
Do I still have to call sd_ble_gatts_value_set() on the characteristic handle [using whatever temporary buffer I would have been using anyway for BLE_GATTS_VLOC_STACK]?
...
Hi,
I would like to use the app_gpiote files from Nordic in combination with the softdevice enabled.
In the app_gpiote.c file interrupts are enabled using the standard...
As far as I can see buttons_init() initializes GPIO and sets up button_event_handler().
button_event_handler() calls ble_lbs_on_button_change() and always set static uint8_t...
I have problems with my iPad to catch data coming from key presses of HID keyboard profile. First, I programmed the dev tool nRF6310+PCA10005 with the HID keyboard profile...
I installed nrfgostudio_win-64_1.15.1_installer, nrfgo_sdk_2.3.0_setup and nrfprobe_v2_0_0_7252 to test nRFgo starter kit(nRF6700). I tried to test uart on nRF24LE1D. but...
