Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Dear Nordic Team,
Thanks for supporting.
Now i am trying to work DFU with NUS example.I am following As per nordic document like: infocenter.nordicsemi.com/index.jsp...
I am trying to communicate with DS1307 (RTC) using TWI on nRF51822.
I have configured the pins, address (0x68 fixed for DS1307), frequency and enabled TWI.
Now I am about...
Dear Nordic,
Some time ago we started a project in which we decided to use ANT protocol to communicate wirelessly. However, now that we are going to production in a very...
my programer have many place use sd_ble_gatts_hvx() send data , if i get the BLE_GATTS_EVT_HVC ,how i know this return value return belong which use sd_ble_gatts_hvx(),how...
how to save a problem,if one Thread use sd_ble_gatts_hvx() send many package ,but i use vTaskDelay(50)( the freertos delay api ) when one package send ,then send another package...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
I read an article about the connection, pairing, bonding and whitelist, there are some doubts：
Bonding...
i want to send data according the ruture value , because we all the data send ruturn value ble_evt_tx_complete ,how i can distinguish difference channel'return value
I've been trying to trying to upgrade some code from SDK 12.1 to 12.3 and it no longer fits in 16k RAM.
I initially thought the problem was this data segment in the linker...
Hi,
I recently started working with the NRF51DK,I need to read data from KX022 accelerometer via I2C and transmit the results over BLE.
I am using TWI_SENSOR example...
when i send many package from programer different place , the return ble_evt_tx_complete have many times. how i distinguish which the ble_evt_tx_complete reture is that place...
I want to add DFU function to ble_app_beacon example,but I don't know what I should do?Who can give me any suggestion?Thanks.
My board is nRF52-DK.SDK is nRF5_SDK_11.0.0_89a8197...
Hello,
i have Nrf52840, here is the code for PWM
APP_PWM_INSTANCE(PWM1, 1);
uint8_t cBuzzer::_PWM_init(uint32_t Time_uS){
app_pwm_uninit(&PWM1);
app_pwm_config_t...
