Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I have a problem with advertising, application starts advertising and makes connection normally, but after disconnection advertising is not starting. sd_ble_gap_adv_start...
Hi,
i am using SDK v8.0
and in main function, initialization like this err_code = bsp_init(BSP_INIT_LED | BSP_INIT_BUTTONS, APP_TIMER_TICKS(100, APP_TIMER_PRESCALER), button_event_handler...
Test code：SDK14 ble_app_ancs_c
Hey guys,
When I used ble_app_ancs_c demo to do FDS, there was a problem！
I initialize FDS and register the drop back function。
When...
I am migrating a project from SDK 12 and SoftDevice S132 V3.0.0 to SDK 14 and SoftDevice S132 V5.0.0. Is the follow case still required in the ble_evt_handler ?
#if (NRF_SD_BLE_API_VERSION...
Now want to use two way PWM, how to set the PWM cycle, frequency, duty cycle, there are two road PWM phase, which is the starting point is not the same as shown in figure...
I am having errors building the examples in the latest SDK for Mesh (nrf5_SDK_for_Mesh_v0.10.0-Alpha_src). I ran cmake -DTOOLCHAIN=gccarmemb -DPLATFORM=nrf52840_xxAA .. in...
Hello,
I'm using NRF52832 with SoftDevice S132, and SDK 14.0.0 to make NUS peripheral and central. To test it I have one NUS peripheral device, that echoes incoming data...
Using SDK 13 FDS, I store 6468 byte, that is 1617 words, including FDS header. Of course this size is total.
In detail in byte size, this size consists of
(12(header)...
Hi,
I'm wondering if the slave connection interval range is the same as the GAP peripheral preferred connection parameters i.e. does it make sense to do the following ...
Hello!
I'm developing thread application with COAP communication. I've got problem with message queue on router. Everything works fine when operating as a child. I have cyclic...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
I'm trying to get started with the nRF51-DK with the ble_app_template. I want to get it working in the Rowley CrossWorks IDE. (From what I understand this is the same...
I am having trouble running softdevice_enable. Here is what happens:
After main(void) starts the code is:
log_init(); // WORKS
clock_init(); // WORKS
buttons_leds_init...
Hello,
I'm using a nRF51822 to send data to the iPhone using the NUS service. I'm using the oldest SDK4.x and v5.x S110 soft device. I know that the least connection interval...
