Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I use the board to act as relay.First ,i scan and connect to one peripheral.Then ,i want to disconnect the peirpheral once the another central connect to my board.i call sd_ble_gap_disconnect...
Hi ,
Would you help me to find right material(App note, source code/project) to implement below case:
My nRF51822 connected on beaglebone black(BBB) over UART this will...
Hi,
I want to implement a DC/DC converter setup schematic for my projet and I don't know how to make the difference between the AVDD and VCC_nRF supply tags given in the...
Hi, all!
I have a Quesion about Maximum Voltage & Current of internal DC/DC conv. & LDO of nRF52832.
I'll design circuit using olny internal DC/DC conv. & LDO of nRF52832...
Hi.
Is there a (lazy) (dummy) comfortable way to make an nRF518 chip (in my case, nRF51822) communicate with the built-in bluetooth adapter of a laptop with windows 7 or...
Hi,
I am trying to connect a GPS through UART to nRF52 and get the reading and write it to the serial USB of my PC. I am using app_uart_init() and app_uart_close(). My idea...
Hi, I would like to handle in the twi_event_handler the case when the p_event->type == NRF_DRV_TWI_EVT_EVT_DATA_NACK differently and not treat it as an internal error.
...
I'm trying to use separate antplus network key, but I still can receive messages from devices that are configured with another key. Device A was using network key 0,0,0,0...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello,
I have designed m custom PCB and i have verfiy my antenna maching network with the spectrum analyser its is perfect matching but the real problem is when i measure...
Hi,
I'm using the Master Emulator DLL to build a VB, everything seems go fine. However I found that if there's a device discovered but fail to connect by some result (eg...
Latest ble-driver-win version is 0.5.0 and supports SDK up to version 8.1.0.
s130 v2.0 needs SDK v11.0.0 (API changed).
So should I understand that ble-driver-win cannot...
In the datasheet it is mentioned that the tx current is 10mA without DCDC. In our board, we are seeing a Tx peak current of 13.5mA. So my question is the does that quoted...
