Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Hello,
I'm trying DFU/bootloader.
Using nus service
Switch to dfu when necessary
At this time, watchdog (2 Sec) enable state does not execute the bootloader...
Hi,
I am mobile developer and very new to mcu programming. Due to our new product's requirements, I have to write program with new bluetooth chip. So if nrf51 and nrf52 series...
To find a clean channel for 2.4g Band to avoid the wifi channel, nRF24L01p would sweep frequency for all the channel (2400M~2525M). But looks like nRF24L01p not support to...
Hello guys!
I'm trying to port the TSS service to one of my projects.
This project is based on SDK13.1 while the Thingy is on SDK12.1
I have a lot of problems with...
Hello guys!
I'm trying to get softblinking led work with a SDK14.
The code works perfectly fine in one of my projects that use scheduler and SDK13.
But in SDK14, (only...
Hi, I think the idea of limiting the behavior of a model to states is very wise, but due to my limited understanding in this matter, I find it puzzling as to what happens...
Is it possible to use the NRF52832 UART in half-duplex single-wire mode, by assigning TXD and RXD to the same GPIO, setting the GPIO drive to disconnect '1' and using a pull...
I am running the example under peripheral\pwm_driver on PCA10040, and SDK 12.2.0. Using a scope, I measured the period (from rising edge to rising edge) on one of the LEDs...
In my project, the softdevice I used was S110
I hope that some of the data can still be retained after OTA updates,
in the Bootloader program code:
#define DFU_APP_DATA_RESERVED...
Hey togehter,
has anyone succeeded setting up a connection between ST-Link and nRF52832?
I connected the pins (GND, SWDIO, SWCLK and second try with GND, SWDIO, SWCLK...
Hi,
Please let me what is the beacon layout of nRF58122 for scanning beacons in region by using following method:
BeaconManager.getBeaconParsers().add(new BeaconParser...
I'm using and NRF52 with S132 and SDK13.0. I'm using Keil as my IDE.
My application acts as a central for smart phones to connect to and also acts as a peripheral to conect...
Hi, I'm a mechanical engineer, an industrial engineer and have a master's degree in control of the dynamics systems. I never get the change to work with ARM architecture before...
Help, what UART output pins that gather all information from the various sensors in the NRF52832 thingy52, to integrate with Raspberry or Arduino, thank you
Hello Community,
I am trying to implement a whitelist in my central device but when I type ble_gap_whitelist_t I had an error of compilation becuase ble_gap_whitelist_t...
