Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello,
has anyone tried new v1.1.0 for nRF6707? If I change the window size to more than original 2.0s, GUI becomes very laggy and it is very hard to stop the recording ...
Hello,
I've been trying to test DFU over UART which has been added in SDK13.1 but after following every resource I've found I always end up with DFU not working
The...
I found this question which partially answered what I am looking for:
devzone.nordicsemi.com/.../
Essentially, if I am creating a new project with my main.c file and...
Hi I am trying to design a custom BLE board using NRF52832 by following the reference layout.
I am new to RF design and I have got a few questions that I would really appreciate...
Hi
I'm trying to implement DFU in my project. So far, after I sending 01-04 to the control point characteristic(1531)，I can get bootloader signal, to be exactly, i can enter...
Hi,
Can we interface a smbus based sensor with NRF51 or NRF52? The only difference between smbus and TWI is the minimum speed requirement which is 10Khz if I am correct...
Dearl all,
I want use the eclipse and gcc together to program the board nRF52840 Preview DK. I was following the tutorial devzone.nordicsemi.com/.../.
I followed the...
Hi,
I'm using nRF52832 with sdk 13.0.0(softdevice 4.0.2).
I had trouble to connect nRF52 and some android 7.0(or upper version) smart device.
I tested samsung galaxy tap...
Hi All,
I am trying to get the serial DFU working with nRF52832 development kit with SDK 13. I am able to get the bootloader flashed and have installed the nrfUtil tool...
since im working on sdk9... advertising program(hello world).i wanted to generate a random address .but i couldnot complete it sucessfully.can you please help me in providing...
Hi
I'm trying to create a DFU package for a SDK11 (insecure) DFU
For just the bootloader I have this syntax in my makefile
nrfutil dfu genpkg --bootloader $(OUTPUT_BINARY_DIRECTORY...
Hello all,
I started working with nrf51 series on mesh networking as i am new to this i want know whether the chipsets will come with preadressed? as it require to adress...
Hello,
recently I was going through this and the following statement concerns me:
First of all make sure you have a
recent Linux kernel installed (at
least 4...
Hi,
I have serious troubles when trying to program the board with softdevice (s140).
nRFGo Studio:
nRFGo Studio installed and running fine. When I connected the board...
