Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi,
I need to support two advertising protocols simultaneously Beacon and iBeacon.
This is because iOS.CoreBluetooth has a lot of limitations (there is no way to identify...
I want to know OBD-II Application scenario
ignore how to get OBD-II information from the car. assume I already get the info
generally, how often fetch the information...
Hello engineers, Recently I test the ADC function,I think the library function is so difficulty for me. So I want to use the ADC by register,but I found that ,after I start...
I am developing on a nrf52 board with a fdc2214 chip. I created 1 custom Service and 3 characteristics shown below, and the format of my UUID is 0000xxxx-1212-efde-1523-785fef13d123...
Hello, I successfully ported one provisioner and one provisionee to 2 nrf52840 experiment boards respectively, now I'm having the provisionee connected to my computer and...
Hi, I asked a relevant questions before and was advised to solicit such information from my local Nordic operations. But they didn't appear to know that either, so I'm here...
Calling ble_nus_string_send() from within a TWI callback (case NRF_DRV_TWI_EVT_DONE) is performing a reset on my PCA10028 (nRF51422). It works fine from the main loop.
...
When I run nrfutil, the program immediately throws a Python exception. It has been working for the last 6 months. I've used pip to try to upgrade protobuf and nrfutil, but...
I AM HAVING A COUNT VALUE WHICH IS IN THE RANGE OF 10000 - 100000 WHICH IS TO BE TRANSMITTED OVER THE BLE (OF THE BOARD) TO THE ANDROID DEVICE. I like to use nus service to...
Not really a development question. I'm looking for a wearable BLE device to use as a prototype for an academic research project (in a healthcare/hospital setting).
The...
Hi there,
Can anyone help me do secure DFU using bluetooth on PC please? I've tried every possible node.js solution to no avail.
I don't care what programming language...
Hello,
To my understanding, normally, either after a reset or powering up, the program should first run to Reset_Handler, then SystemInit, then __main.
Somehow, my program...
i used RTS service example in nRF5_SDK_13.1.0_7ca7556.
I entered the value in cccd,then i see ATT_ErrorRsp: status=0 oc=0x0012 h=17 err=5.
What's wrong with it and how...
We have tried working with nrF UART android source code from Github, it is not working, we have connectivity issue. it is working fine with the uart application which we have...
Hello, I'm developing firmware for a custom PCB with an nRF52832 chip. I've implemented almost all of the peripheral functionality I need (including TWI, GPIO, GPIOTE, delay...
