But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
I am trying to send sensor(accelerometer) data through beacon. I am basing my logic on the beacon example. I am putting my sensor data into an array and passing it...
Hi,
I have an nRF51 DK, found here www.nordicsemi.com/.../nRF51-DK .
I am using SDK V11.0 and S130 V2.0.
I am developing on a Linux machine.
I can compile and run...
Hi.
I'm using the Power Profiler Kit and the PPK desktop application to log the power consumption of my device. This works well for short time spans.
However, I'd also...
Hi
I'm trying to delete all files with a given file id. Will fds_file_delete() delete all files with a given file id, or just the first one it finds?
thanks
SDK1...
Hi
I'm trying to use fds_record_find() to detect if a record exists in flash storage. After erasing the device (via nrfjprog), flashing the softdevice, flashing the program...
I use an app_timer to periodically update sensor reading in my application. There is a characteristic used to change updating rate by stopping and restarting the app_timer...
Hi,
I work on a project for the nRF52832 with Keil µVision using ARM Compiler V5.06 update 2 and nRF5 SDK 11.
In a module I allocate quite some memory using malloc(...
For the BLE GAP advertising flags byte in the advertising data, we have the following options:
/**@defgroup BLE_GAP_ADV_FLAGS GAP Advertisement Flags
* @{ */
#define...
I cannot seem to save the new Device Name value in the nRF51822 beacon.
I am using the mobile app nRF Connect.
This is my procedure:
1).Run nRF Connect on Android device...
Hi Nordic Team;
I am using nrf51822 devices with sdk12.3.0. I am using buttonless dfu example without any problem with sdk12.3. However, I see that you realese sdk14 that...
We're considering nRF51/52 to implement a specific BLE application. We need the nRF51/52 go to sleep if a BLE collision signal or interference on an advertising channel has...
Hi,
I'm using nRF5_SDK_13.0 on nRF52840 based on ble_app_hrs_rscs_relay example. I use it to connect a bluetooth 4.0 device and it's ok now. Also I have a bluetooth 5.0...
Hello, our device is able to be used by Iphone and Andriod. For the ANCS, we have tested the Iphone and it is OK. However, Andriod notification does not need the ANCS. As...
Hi
I'm trying to create a custom ble service with 4 notify characteristics.
Everything works with one characteristic, but when i add the other the DK hangs.
I'm using...
According to the NRF52810 datasheet，to ensure optimal performance it is essential that you follow the schematics- and layout references closely.Then if I want to use NRF52810...
