I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
I've been testing my application and am having an issue opening MasterEmulator sometimes. I need to reseat the nfr51 dongle to clear out the errors I am seeing below. Any...
Hi,
I get error NRF_ERROR_INVALID_PARAM or error 0x12 from sd_ble_gap_connect in central.
I even changed peer_addr.type to 0 (BLE_GAP_ADDR_TYPE_PUBLIC).
When scanning find...
Hi, I'm trying to use an MDBT40 based board as a sniffer using the NRF sniffer firmware. I'm guessing I just need UART -> USB to talk to the chip, so I've hooked it up to...
Hi,
I am trying to figure out the best way to save power on the nrf52. I need to connect with ble about two times per day. The ble should 'woken up' by an accelerator ...
How can I flash both the dfu bootloader and an application, and have the application run after the flash?
As soon as I flash the bootloader, it kicks in doesn't fire the...
Hi,
While updating from the antique NRF51 SDK8.1.0 to the newer SDK 12.2.0, I came across a problem: Gcc crashed with:
c:\users\elm\documents\nordic\nrf5_sdk_12.2.0_f012efa...
Hi all,
i have some problem to use Timer0_IrQ.
i start first with a program that use a softdevice. After i want change this project with another that don't use it.
...
Hi,
I would like to know if the NRF51822 (Just the NRF board, not the BLE Nano) comes already prepared to be programmed or if it needs some modification. I want to program...
Hi,
I have successfully implemented the UART over BLE. Now I'm trying to implement the HID over GATT for my nrf8001 device. What I'm trying to achieve is lower connection...
Hello,
I am attempting to setup a SPIS interface, and I am continuously getting 0x00 inside my RX buffer. I am varying the length of TX from the SPI master, and seeing...
Hi,
Is nRF Sniffer able to trace BLE4.2 link with LE Data Packet Length extension?
I would like to be able to track the packets up to maximal theoretical data throughput...
Hi
i want to have a concurrent connection in nRF51822 with BLEs and some nRF24l01+.
is it possible ?
is available example
for it ? which SDK support ?
...
Hi, I am tring to build and compile the SDK 12 DFU bootloader_secure .
I am getting an error:
"unable to allocate space for sections/blocks with a total estimated minimum...
I am using nrf51822 Dongle with nordic-sdk_10 and s130 softdevice. Tried to flash the dfu bootloader and using examples/ble_peripheral/ble_app_dfu_template app for OTA.
...
