Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Dear sirs, I've had a difficult time establishing communication between my nRF24L01+ board and the SPI bus on my Arduino Uno R3 microcontroller. Could you please provide me...
Hi all,
I am thinking of using a GPIO pin's "SENSE LOW" to wake up my device from SYSTEM OFF mode.
In order to avoid the device keeps waking up in case the pin stays low...
I am using an nrf51822 DK with a (so far) very simple code along:
main()
{
//... init I/O
run();
}
Inside run:
run()
{
uint32_t retval = NRF_SUCCESS;
...
Hey,
I recently got the nrf52 DK and tried to make use of the app_button library to have easy to use debouncing.
As far as I understood the library, the event should be...
Hi,
i have a problem withr the example "BLE ATT_MTU Throughput Example".
I flashed the soft devive with nRFgo Studios. Now I want to flash the example, but i got following...
I have want to make application where beacon sends data to NRF52 and NRF52 to PC.
But if for example, the connection between NRF52 and PC is through bluetooth instead to...
Hi,
I have bought a new nrf52840 PDK. I have gone through the PDK user guide and I came to know that we can use qspi pins as gpios by cutting the Solder bridge connections...
Hi All,
I am getting following error while compiling template example with DSP CMSIS library in IAR.
Fatal Error[Pe035]: #error directive: "Compiler generates FPU instructions...
Hello,
I have a question regarding AVDD(35/36) pin. I am using nRF51822 QFAA package. And the reference circuitry on the datasheet uses a 1.0nF capacitor between AVDD and...
Hi, my first post here.
I'm a undergraduate student and newcomer to this field. I've some programming background but few in electronics and embedded systems (so probably...
Hi all,
Is there any DFU example using dual bank to the SDK 12.2? The secure bootloader example is for single or dual bank? . Sorry for the question it is no clear to me...
I have purchased nRF51822 Evaluation Kit.
So I should be able to download Android code. Correct?
But when I go to
www.nordicsemi.com/.../nRF-Temp-for-Android-4.3
...
Hello,
When I try to use the DFU function, I received 8202 error from nrf Toolbox.
My environment is as follow:
SDK version: 12.2.0
SoftDevice version: S132 3.1.0.
...
I got pca10040 dk and I am trying to run the code that was sent to me earlier by one of nordic employee. I could compile it without errors but I cant see any advertising data...
