Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
I have taken a look the APIs which the S132 supports in nRF52 DK.
However i could not find the APIs that can initiate the channel map update ,feature exchange & version exchange...
hai
i have this code to save and read some data in flash.but the stored and read data are not same. always reads zeros. how can i solve that.........?
here is my code...
I'd like to be able to quickly update the advertising data using
sd_ble_gap_adv_data_set()
and at the moment I'm doing this via a bit of a hack, as I captured the advertising...
Normally, Raw data has TYPE (0x01), TYPE (0x09): device-name, TYPE (0X07): UUID 128 bits.
However, there are devices without TYPE (0x07).
Is this also a problem?
Communication...
Considering using an nRF52 module, I'm developing using EvoThings' native plugins right now. I don't think we have the resources to do IOS and Android native apps.
Has...
I have an application where my nrf52832 acts as a peripheral and I can connect to it without problems, but after some time like aprox 10 minutes when I try to connect to it...
Hi!
I have searched for this questoin, but not found anything useful. Probably I an not using a good search phrase.
How do I determine how much space is left on a nRF51...
This is a general question I will throw out initially, but I can get more specific if necessary. This is something I see a lot in my year or so of development with nordic...
SDK:8.1.0
Chip:51822AAHO
Hi,i use the nRF51822-PSV3.1 Schematic diagram.The chip set 4dbm tx power,
then i test the test point(C6) as follow,2402MHZ and 2426 MHZmax...
Hi,
I run the HID keyboad example, and a problem confuses me. I use the "lightblue" APP to connect the peripheral--"Nordic Keyboard", but the iphone appears a pairing box...
Hello!
I have been working recently with the PCA20006 Beacon board. The example we have tested is the ble_app_beacon that allow us to change the UUID/Major/Minor and go...
This may be a stupid question, but...
What value is BLE_GATTS_ATTR_LENS_MAX
Its mentioned a lot in the SDK, but I can't actually find a value for it actually defined...
I would like to know how to add Service Change UUID: 0x2A05 Properties: INDICATE Descriptors Client Characteristic Config UUID: 0x2902 to Generic Attribute of Nordic_HRM....
