Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hello,
I am developing a board with the SIP nRF9151.
I'm designing the board with a shared antenna for both the GNSS and LTE signals (Ignion NN02-224).
For the antenna...
I have been able to use external flash with Octal SPI mode on an nRF54H40-DK:
❯ west build -- pristine -- board nrf54h20dk / nrf54h20 / cpuapp zephyr / samples / drivers...
Hello, I want to implement a project with BLE mesh. Several nRF52480 boards should form a mesh and e.g. send the status of one of their buttons to a tablet. What would be...
How many nRF52840 chips can be used simultaneously? Can all data and advertisement channels be used at maximum capacity (2Mbps/each) to result in an overall throughput of...
Hi,
I am running an nrf52 (board PTR5628, no external 32kHz crystal), having some leds blinking at startup just prior to start advertising. 75% of the time when I power it...
Hello all,
I have created a BLE application on nRF52 PCA10040 devboard with S132 SD, in which I would like to use a PWM with the PWM_Driver .
My pwm source code as below...
Hello,
I am new to nordic nrf51822 and want to program nrf51822- www.raytac.com/.../MDBT40 spec-Version A5.pdf using jlink ( world.taobao.com/.../537881589911.htm .
I...
Dear friends,
As it said in title,when using 52832,s132 softdevice,what is the max number of packets that can be sent in one connect interval ? In which document i can get...
I have run into a challenge with the app_twi API, and I'd like to run it by you for your advice. To be clear, I am not blocked. But I am not pleased with the source code maintainability...
Hello,
I'm trying to implement DFU support to our application on nRF52832. I got it working fine with SDK11 SD2.0, but now SDK12.2 SD3.0 is causing "gray hairs". I used...
i have a nrf51822 mcu device, when it ok, i use Ultrasonic bonding technology to Assembled box,and today,many device crashed,is it related to ultrasonic?
Hi,
this is for anyone having problem with the eddystone EID after reboot. There seems to be a problem that the EID slot will write the encrypted IK to flash instead of the...
I'm having issues with my application implementing DFU. I added the DFU service in my application and can get into the bootloader. I have added my own key to the bootloader...
I'm migrating form S332 0.9.1alpha (aligned to S132 2.0.0) to the newer S332 2.0.1 (aligned to S132 3.0.0) on a nRF52 board, and I'm seeing a new characteristic under Generic...
Hello,
I am trying to configure gpiote to give an interrupt for wake on motion functionality in MPU9250
I am configuring the MPU for that by calling separate wake_on_motion...
I tried to run some examples from pc_ble_driver_py but i always end up with the following exception.
(using python 2.7.9)
Traceback (most recent call last):
File ...
I have an application developed using S110 v7.3.
I want to upgrade to v8.0 to get additional features (over air update, DC/DC converter etc.), but notice S110 is not supported...
