hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
It looks like NFC_T4T_EVENT_NDEF_UPDATED gets passed as the event attribute in the nfc_callback function whenever a new NDEF message is written.
Is this expected behavior...
Hi,
I have an aconno module ( http://aconno.de/acn52832/) and I am trying to program it via DK52.
I wired the module as follows:
Module Vcc (pin 12) -> DK52 VDD...
Hi all,
I am trying to get the ble template of SDK12.2 working in eclipse using a managed makefile. The softdevice I use is s132 v3.0.0. The board is an evaluation kit...
Hi Nordic,
I'd like to know what the maximal current draw from the internal REG0 is to power external components. The only thing I could find in the datasheet that says...
HEllo,
I am trying to compile for the nrf52 one of the examples that are included in its SDK12.2, to be precies, I am using experimental_ble_app_blinky_pca10040_s132 ,...
I have noticed that the reference schematic (the original if you can call it that, not the 1v8 or DC/DC) for nRF51x22-QFAA, QFAB and QFAC have different value capacitors and...
Hello,
I cannot use the nRF Sniffer because it is always crashing. This is a confirmed bug in the Software and the OSX client written is working flawlessly.
I have experimented...
Hello,
I am newbie with KEIL/SEGGER, I have been following this tutorial to compile the example experimental_ble_app_blinky_pca10040_s132 for my nrf52 chip, the project...
Hello,
I am using sdk 12.2.2 and nrf51 dev kit. I am trying to upload ble_app_gls example code over the air to nrf51 dev kit. I can find only secure_dfu code in the sdk....
I am considering build some of my own shields to interface with the nRF52DK for the 832 and 840. I am curious how I should use header P5 with the shield detect pin. Should...
Hello,
I am trying to implement my custom service with NUS. I have gone through almost all the solutions presented on this forum.
Observations:
The board does...
Hi,
I need to be able to change the GAP parameters of my connection for only a short period of time to save battery life but have high throughput when I need it. My firmware...
