Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
I've discoverd a strange behaviour with nrf51822 CEAAD00 Revision 2.
I am using NRF_POWER->SYSTEMOFF = 1; for powering down the chip and a sense signal for wakeing up....
Hi,
I have downloaded the hardware files of nrf51822 beacon kit.
How to change the pcb layout of nrf51822. ( remove the name on the pcb, change the form of the pcb etc...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
i have a strange problem which happens when i use scan mode to get 3 separate channels on saadc.
For example when i use uint32_t ticks = nrf_drv_timer_us_to_ticks...
Hi, I use Keil 5 and SDK 13.0.0 in Windows 7 64bit desktop.
I wished to test the SDK 13's BLE UART example.
However, even though I clicked "Check for Updates"...
basically i tried am trying the easiest ble example
ble_app.becon_pca10040
i tried the following.
use keil to upload into the nrf52 Evalutaion board. the led is...
Hello, i have been looking for a good development environment to use for my nrf52832 on linux. I have only found a few repositories on github pertaining to this. Not very...
Hello,
Does someone know a good J-link segger for programming the nrf51822 smart beacon kit?
And do u need a 6-pin j-link segger for the nrf51822 smart beacon kit?
hello ,
I am interfacing Grideye AMG8832 with Nrf51822. The initialization part is executed without errors but ON trying to recieve or transmit it gives error of TWI as...
Hi Nordic developers.
I am developing a custom board using 2 Rigado BMD-300, but I am unable to run my 100% operative program or examples.
At first time I was able to...
Hello,
I am using SDK 12.2 currently but I would like to follow the BLE Tutorials offered on this site, which I see were written for SDK 11.0. Will I have any issue following...
Trying to program an MDBT42Q nRF52832 based BLE module from an nRF52-DK as external target on connector P20.
I used to do this with nRF51-DK and external nRF51 modules with...
Our product is a peripheral on the nRF51822. We develop on Mac and use gcc, make, etc with Visual Studio Code rather than Eclipse. Recently, we started getting close to production...
Hello,
I would be interested on knowing whether I may have a secondary UART on the nrF52 chip or not. I would like to communicate my nRF52 with a RN2483 and this is done...
Hi
I've just looked into the new released SDK 13.0.0 with support for the new S132 4.0.2 and the new PCA10056. On line in the release notes reads "This release does not...
