Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
I have been successfully using my nRF52 Dev Kit (PCA10040) for the last few days. Today, when messing around with the UART drivers, I seem to have messed up the JLink-OB....
Hello,
I have an NRF51822 beacon board and two small 0.96" OLED displays (does not matter for me which one o use). One with GND, VDD, D0, D1, REST, D/C, CS and VCC pins...
I'm on windows 8 using the 1.0.1 sniffer application and wire shark 1.10.14 64bit with a Nordic nrf51 dongle. I'm using an nrf51 dev board with ble_peripherals/ble_app_blinky...
with nrf51 there is 2 blocks (block0 for softdevcie and block1 for user data and stack). I configured the system to retain RAM before going down using sd_power_ramon_set(0x00030003...
Hi,
I have a device that is configured to work in GAP central role. This device only scans for specific advertisements from specific devices. Could you suggest how I can...
Hi!
I used the develop board test the application "ble_app_multilink_central" and "ble_app_multilink_peripheral",but it is always connected failed,and disconnect Reason 0x0008...
Hi there. I have a very long C code that is running correctly on Code:Blocks, Ubuntu Terminal ( using GCC ), Eclipse and on Dev-C++.
However, when I put in on the board...
Hello,
I've been trying to control MCP23017 IO expander with TWI using nRF52832. When I execute the code it stops at nrf_drv_twi_tx. The address pins A(0:2) are 0.
Any...
I have having following configuration:
I want a fail safe method to update firmware on nrf51822 using attached host controller. I looked at serial wire debug interface...
Hello,
I'm running a serialized application based on the SDK 10 and S130 v1 and I am in the process of porting the peer manager to the application µC.
Due to the fact...
I'm trying to set up a system where the sample rate of data being notified to the client from various sensors can be changed by updating a configuration characteristic in...
Hi all,
I have one nRF52 DK board (PCA10040), and I have installed necessary JLINK drivers when first connecting the board to PC, it can displays the virtual COM port correctly...
I have a board here with nrf52832 rev B attached to a max98089 i2s codec. In this application we are only really using the ADC channel of the codec. Everything is configured...
Hi NordicS
Do you have a code example for a central UART application?
I am looking for a example that acts just like the nRF Uart App, but running on e.g. a PCA10031...
