Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi
I'm trying to explore the nRF52-DK kit.
I downloaded the demo : www.nordicsemi.com/.../heart_rate_demo.zip
Dragged and dropped the hex-file to the JLINK drive thats...
Hello,
I am utilizing an accelerometer sensor and communicating with it using TWI (I2C). I have both a development kit (NRF51-DK) and the Beacon (nRF51822-Beacon). I can...
Hi all:
Below is my source code for SPI master.
However, the handler is not triggered ...
Is any setting I missed?
Thanks...
void spi_event_handler(nrf_drv_spi_evt_t...
Hi,
I am using nRF51822 BLE nano with mbed IDE. I tried to set channel so that i can achieve the desired frequency for FCC testing i.e. 2402MHz,2441MHz and 2480MHz .I am...
I am looking at the ble_app_hrs_c example (with the s130 soft device on pca10028 dev board). I have set the m_scan_mode to BLE_WHITELIST_SCAN to enable whitelisting. In the...
I have implement the systick with the idea to use it for delay functions.
The systick is running normal if no BLE Events occur, but during a BLE event it seems to be stopped...
Do conditional breakpoints work in Keil uVision5? I open the Breakpoints window and see:
If I set count to any value, I application still breaks on the first pass. When...
Hi
I have problem make the examples in the SDK 11. I get at "No rule to make target"
C:\konskimo\NYII\Spec\nRF52832\nRF5_SDK_11.0.0_89a8197\examples\peripheral\blink...
Hi,
when using timeslots I cannot turn off the external crystal that causes an higher consumption.
I already read this post and tried to turn off the timer0 (using STOP...
Dear Sir,
I merget (Software Device) + (DFU bootloader) + (Application firmware) into PE280_WS.hex
And use the script <<nrfjprog.exe --program PE280_WS.hex>>
it reported...
I'm having trouble building the ble_app_uart example in: SDK11/examples/ble_peripheral
My build environment is:
Ubuntu 15.04
SDK 11.0
GCC
S130
PCA10000
nRF51822_xxaa...
Hi,
I have a pretty hard time to get I2C/TWI running on my 52832 Dev-board (pca 10036).
My problem is, that i do not get any physical I2C signal out of the board's pins...
Hello, this might be a silly question, but i've seen various Nordic examples and i don't know whats the difference?
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500, UNIT_1_25_MS...
nRF52 series compatibility matrix says that you can get the IC revision using nrf_ic_info_get but it is only implemented for nRF51. Does the following patch add support? ...
