Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic Team,
I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
From bLE RF sniffer user guide:
To set up the Sniffer you will need one of the following pieces of hardware:
• nRF51822 Evaluation Kit (PCA10001) and a mini USB cable...
hi, i am a beginer in BEL application.
after some tries, i can compile and download 'ble_app_uart'.
but the module does not work at all also it dosen't advertising....
...
i make a new "Makefile! project" using example in SDK first i use the "blinky" ,
it looking likes can be work, then i try to use " blr_app_hrs_c " ,
i do the same step to...
I am trying to have the dk (i have the 10036 preview) send pwm signals to a motor controller so that i can direct its speed. I have based a lot of the code below of this utorial...
Hi, I have seen that on mbed compiler, there is a bootloader that include the DFU and with this, we should not implement DFU in application.
In keil, we must implement...
During Power Off mode the nRF52 GPIOs stay retained. But by waking up on a external Pin we can see another Pin toggles for approx. 600ns. It seems this happens during the...
Hi, all.
I'd like to broadcast only when i want to inform nortification.
flow like
No advertising when application start.
Check the events that there...
I'm trying to develop a minimalist android app to send and receive data with my nrf51822 dev-board.
Can anyone please tell me where I can find a great project example?...
Hello,
In our project i am using nrf51822 with stack Softdevice S110 . We want to connect it with Samsung Gear S2.Is it possible with stack s110 or i have to use stack...
When the device powers up I want to grab the device name from a known location and also rewrite that same location when I get a new device name. How can I write to the internal...
Suppose you want to send 20 bytes of data using API sd_ble_gatts_hvx, do you need to punctuate the first 16 or so data within the 20 bytes sent with a CRC ?
it may seem...
Hi, all. I use nrf52 and softdevice(S132).
I'd like to know SoftDevice process timing to hardware.
Can it be ?
I know, SoftDevice Specification in "Processor availability...
Hello,
I have an development kit NRF51 and wrote a code for it which uses uart, ble advertising and ble scan. It works pretty well on the kit.
The problem is when I...
Hi,
I use a personnal GAP Address, but it must be the type used:
-Public address.
-Random Static address.
-Private Resolvable address.
-Private Non-Resolvable address...
Hi,
I am trying to get the dfu single bank bootloader ( github.com/.../nrf51-dfu-single-bank-ble) supplied by Nordic to work. I can successfully push firmware to my device...